Standard Bidding Document

📑 Procurement Notice (NIT)

Establishment of Online Examination System

Published on: Friday, September 25, 2026 11:00 AM

Ref# : P128944
QR Code

REQUEST FOR BIDS

PROCUREMENT OF GOODS

  1. The Federal Medical College (Federal Medical College) has reserved Funds for the procurement planned for FY 2026-27. The Federal Medical College (Federal Medical College) intends to apply part of the proceeds of this Fund to cover eligible payments under the contract for the "Establishment of Online Examination System" with the reference of "P128944"
  2. The Federal Medical College (Federal Medical College) invites sealed Bids from eligible Bidders for procurement of goods described in the bidding documents on EPADS v2.0.
  3. Single Stage-Two Envelope will be used by adopting Quality and Cost Based Selection (QCBS) Technique for the subject procurement, in line with the Public Procurement Rules, 2004 and any Regulations, Regulatory Guides, Procurement Guidelines or Instructions issued by the Authority from time to time.
  4. All Bids must be accompanied by a Bid Security amounting described in Bid Security Section in Bidding Document in the form of  Pay Order, Demand Draft or all bids must be accompanied by bid securing declaration in the format specified in the Bidding documents
  5. E-Bidding documents, containing detailed terms & conditions, specifications and requirements etc. are available on e-Pak Acquisition and Disposal System (EPADS) at https://epads.gov.pk/opportunities/federal/procurements/128944 for all the interested bidders registered on EPADS v2.0. Bidders are required to get themselves registered on EPADS v2.0 to participate in Bidding process.
  6. The e-bids, prepared in accordance with the instructions in the e-Bidding Documents, must be submitted through EPADS v2.0 on or before Wednesday, October 14, 2026 11:00 AM. E-bids will be opened using EPADS v2.0 on the same day at Wednesday, October 14, 2026 11:30 AM. Manual submission of Bids shall not be entertained. Those vendors who have not yet registered on the new version of EPADS v2.0, may register themselves on https://vendors.epads.gov.pk/. A tutorial to explain the registration process is available at https://www.youtube.com/watch?v=MNW6T38v7tc

In terms of Rule 48 of Public Procurement Rules, 2004 Grievance Redressal Committee (GRC) is notified for the subject procurement and notification copy is available on the procuring agency’s website and on Authority’s website at (www.ppra.org.pk).

 

 

Federal Medical College (Federal Medical College), IT Assistant
Federal Medical College, Hanna Road, G-8/4, Islamabad
+92-333-525196
info@fmcisb.edu.pk

📑 Instructions to Bidders (ITB)

Establishment of Online Examination System

Published on: Friday, September 25, 2026 11:00 AM

Ref# : P128944
QR Code

A. Introduction

1.Scope of Bids

1.1 The Procuring Agency (PA), as indicated in the Bids Data Sheet (BDS) invites Bids through EPADS v2.0 for the provision of Goods for as specified in the BDS and in Section V – Evaluation Criteria, Specifications & Schedule of Requirements. The name, identification, and number of items/deliverables are provided in the BDS. The successful Bidders will be expected to provide the goods within the specified period and timeline(s) as stated in the BDS.

2. Source of Funds

2.1 Source of funds is referred in Clause-1 of Invitation for Bids.

3. Eligible Bidders

3.1  A Bidder may be natural person, company or firm or public or semi-public agency of Pakistan or any foreign country, or any combination of them with a formal existing agreement (on Judicial Papers) in the form of a joint venture, consortium, or association. In the case of a joint venture, consortium, or association, all members shall be jointly and severally liable for the execution of the Contract in accordance with the terms and conditions of the Contract. The joint venture, consortium, or association shall nominate a Lead Member as nominated in the BDS, who shall have the authority to conduct all business for and on behalf of any and all the members of the joint venture, consortium, or association during the Bidding process, and in case of award of contract, during the execution of the contract.

3.2  Verifiable copy of the agreement that forms a joint venture, consortium or association shall be required to be submitted as part of the Bid.

3.3  The appointment of Lead Member in the joint venture, consortium, or association shall be confirmed by submission of a valid Power of Attorney to the Procuring Agency.

3.4  Any bid submitted by the joint venture, consortium or association shall indicate the part of proposed contract to be performed by each party and each party shall be evaluated (or post qualified if required) with respect to its contribution only, and the responsibilities of each party shall not be substantially altered without prior written approval of the Procuring Agency and in line with any instructions issued by the Authority.

(The limit on the number of members of JV or Consortium or Association may be prescribed in BDS, in accordance with the guidelines issued by the PPRA).

3.5  The invitation for Bids is open to all prospective suppliers, manufacturers, or authorized agents / dealers subject to any provisions of incorporation or licensing by the respective national incorporating agency or statutory body established for that particular trade or business. Procuring agencies shall specify the registration/licensing requirements for the foreign bidders keeping in view the requirement of that business.

3.6  A Bidder shall not have a conflict of interest. All Bidders found to have a conflict of interest shall be disqualified. A Bidder may be considered to have a conflict of interest with one or more parties in this Bidding process, if they:

  1. are associated or have been associated in the past, directly or indirectly with a firm or any of its affiliates which have been engaged by the Procuring Agency to provide consulting services for the preparation of the design, specifications and other documents to be used for the procurement of the Goods to be purchased under this Invitation for Bids.
  2. have controlling shareholders in common; or
  3. receive or have received any direct or indirect subsidy from any of them; or
  4. have the same legal representative for purposes of this Bid; or
  5. have a relationship with each other, directly or through common third parties, that puts them in a position to have access to information about or influence on the Bids of another Bidder, or influence the decisions of the Procuring Agency regarding this Bidding process; or     
  6. Submit more than one Bid in this Bidding process.

3.7  A Bidder may be ineligible if –

  1. he is declared bankrupt or, in the case of company or firm, insolvent;
  2. payments in favor of the Bidder is suspended in accordance with the judgment of a court of law other than a judgment declaring bankruptcy and resulting (in accordance with the national laws) in the total or partial loss of the right to administer and dispose of its property;
  3. the Bidder is convicted, by a final judgment, of any offence involving professional conduct;
  4. the Bidder is blacklisted locally or by international organizations and hence debarred due to involvement in corrupt and fraudulent practices, or performance failure or due to breach of Bid securing declaration.  

3.8  As and when required, bidders shall provide to the Procuring Agency evidence of their eligibility, proof of compliance with the necessary legal requirements to carry out the contract effectively.

3.9  Bidders shall submit Bids relating to the nature, conditions and modalities of sub-contracting wherever the sub-contracting of any elements of the contract amounting to more than ten (10) percent of the Bid price is envisaged.

4. Eligible Goods and Related Services

4.1  All goods and related services to be supplied under the contract shall have their origin in eligible source countries, and all expenditures made under the contract will be limited to such goods and services. For purpose of this Bid, ineligible countries are the countries declared ineligible by the Federal Government. 

5. One Bid per Bidder

5.1  A bidder shall submit only one Bid, in the same bidding process, either individually as a Bidder or as a member in a joint venture or any similar arrangement.

5.2  The Bidder shall not engage a subcontractor for any portion of the contract if the value of such subcontracting exceeds thirty percent (30%) of the total contract amount.

6. Cost of Bidding

6.1   Any cost incurred by the bidder relating to the preparation and submission of its Bid shall be borne by the bidder, and the Procuring Agency shall in no case be responsible or liable for those costs, regardless of the conduct or outcome of the bidding process.

B. Bidding Documents

7. Contents of  Bidding Document

7.1  The Goods required, Bidding procedures, and terms and conditions of the contract are prescribed in the Bidding Documents.  In addition to the Invitation for Bids, the Bidding documents which should be read in conjunction with any addenda issued in accordance with ITB 9.1 include:

Section I -Invitation to Bids

Section II Instructions to Bidders (ITB)

Section III Bid Data Sheet (BDS)

Section IV Evaluation Criteria, Specifications, Schedule of Requirements

Section V Bid Forms

Section VI General Conditions of Contract (GCC)

Section VII Special Conditions of Contract (SCC)

Section VIII Contract Forms

7.2  The Bidder is expected to examine all instructions, forms, terms and specifications in the Bidding documents. Failure to furnish all the information required in the Bidding documents through EPADS v2.0 will be at the Bidder’s risk and may result in the rejection of his Bids.

8. Clarification of Bidding documents

8.1  A prospective Bidder requiring any clarification of the Bidding documents may notify the Procuring Agency through EPADS v2.0.

8.2  The Procuring Agency will within three (3) working days after receiving the request for clarification, respond to any request for clarification through EPADS v2.0 provided that such request is received not later than three (03) days prior to the deadline for the submission of Bids as prescribed in ITB 22

8.3  Copies of the Procuring Agency's response will be forwarded to all identified Prospective Bidders through EPADS v2.0, including a description of the inquiry, but without identifying its source.

8.4  Should the Procuring Agency deem it necessary to amend the Bidding document as a result of a clarification, it shall do so following the procedure under ITB 9.

8.5  If indicated in the BDS, the Bidder’s designated representative is invited at the Bidder’s cost to attend a pre-Bid meeting at the place, date and time mentioned in the BDS. During this pre-Bid meeting, prospective Bidders may request clarification of the schedule of requirement, the Evaluation Criteria or any other aspects of the Bidding document.

8.6  Minutes of the pre-Bid meeting, if applicable, including the text of the questions asked by Bidders, including those during the meeting (without identifying the source) and the responses given, together with any responses prepared after the meeting will be uploaded on EPADS v2.0. Any modification to the Bidding documents that may become necessary as a result of the pre-Bid meeting shall be made by the Procuring Agency exclusively through the use of an Addendum pursuant to ITB 9. Non-attendance at the pre-Bid meeting will not be a cause for disqualification of a Bidder.

9. Amendment of Bidding documents

9.1  Before the deadline for submission of Bids, the Procuring Agency for any reason, whether at its own initiative or in response to a clarification requested by a prospective Bidder or Pre-Bid meeting may modify the Bidding documents by issuing addenda through EPADS v2.0.

9.2  The Procuring Agency shall promptly publish the addendum through EPADS v2.0.

9.3  Any addendum issued including the notice of any extension of the deadline shall also be communicated through EPADS v2.0 to all the bidders who have already submitted their bids. Such bidders shall have the right to withdraw their already submitted bid and re-submit the revised bid prior to the original or extended bid submission deadline.

9.4  To give prospective Bidders reasonable time in which to take an addendum/corrigendum into account in preparing their Bids, the Procuring Agency may, at its discretion, extend the deadline for the submission of Bids through EPADS v2.0:

Provided that the Procuring Agency shall extend the deadline for submission of Bids, if such an addendum is issued within last three (03) days of the Bids submission deadline.

C. Preparation of Bids

10. Language of Bid

10.1  The Bid prepared by the bidder, as well as all correspondence and documents relating to the Bids exchanged by the Bidder and the Procuring Agency shall be written in the English language unless otherwise specified in the BDS.  Supporting documents and printed literature furnished by the Bidder may be in another language provided they are accompanied by an accurate translation of the relevant pages in the English language unless otherwise specified in the BDS, in which case, for purposes of interpretation of the Bidder, the translation shall govern.

11. Documents and samples Constituting the Bid

11.1  The Bid prepared by the Bidder shall constitute thedocuments required in the BDS.

Details of sample(s) where applicable and requested in the BDS.

1.  Documentary evidence established in accordance with ITB that the Bidder is eligible and/or qualified for the subject bidding process;

2.  Documentary evidence establish that the Bidder has been authorized by the manufacturer to deliver the goods into Pakistan, where required and where the supplier is not the manufacturer of those goods;

3.  Documentary evidence establish that the goods and related services to be supplied by the Bidder are eligible goods and services, and conform to the Bidding Documents;

4.  Bid security or Bid Securing Declaration furnished in accordance with ITB 18.

12. Documents Establishing Eligibility of the Goods and Conformity to Bidding documents

12.1  To establish the conformity of the bidder to the Bidding document, the Bidder shall furnish as part of its Bids the documentary evidence that Goods provided conform to the technical specifications and standards.

13. Documents Establishing Eligibility and Qualification of the Bidder

13.1  The Bidder shall furnish, as part of itsBid, all those documents establishing the Bidder’s eligibility to participate in the Bidding process and/or its qualification to perform the contract if its Bid is accepted.

14. Form of Bids

14.1  The Bidder shall fill the Form of Bid furnished in the Bidding documents.The Bids Form must be completed without any alterations to its format and no substitute shall be accepted.

15. Bids Prices

15.1  The Bids Prices quoted by the Bidder in the Form of Bid and in the Price Schedules shall conform to the requirements specified below or exclusively mentioned hereafter in the Bidding documents.

15.2  All items in the Schedule of Requirement must be listed and priced separately in the Price Schedule(s). If a Price Schedule shows items listed but not priced and neither explicitly denied, their prices shall be construed to be included in the prices of other items.

15.3  Items not listed in the Price Schedule shall be assumed not to be included in the Bid, and provided that the Bid is still substantially responsive in their absence or due to their nominal nature, the corresponding average price of the respective item(s) of the remaining substantially responsive Bidder(s) shall be construed to be the price of those missing item(s)

15.4  The Bid price to be quoted in the Form of Bid in accordance with ITB 14.1 shall be the total price of the Bid.

15.5  The Bidder shall indicate on the appropriate Price Schedule, the unit prices (where applicable) and total Bid price of the Goods it proposes to provide under the contract.

15.6  Prices quoted by the Bidder shall be fixed during the Bidder’s performance of the contract and not subject to variation on any account. A Bid submitted with an adjustable price will be treated as non-responsive and shall be rejected.

16. Bids Currencies

16.1 Prices shall be quoted in Pakistani Rupees unless otherwise specified in the BDS in accordance with Rule 30 (2) of the Public Procurement Rules, 2004.

17. Bids Validity Period

17.1  Bids shall remain valid for the period specified in the BDS after the Bid submission deadline prescribed by the Procuring Agency. A Bid valid for a shorter period shall be rejected by the Procuring Agency as non-responsive. The period of Bid validity will be determined from the complementary Bid securing instrument, i.e. the expiry period of Bid Security or Bids Securing Declaration as the case may be.

17.2  The procuring agency shall ordinarily be under an obligation to process and evaluate the bid and to issue letter of award within the stipulated bid validity period.

17.3  Under exceptional circumstances, prior to the expiration of the initial Bid validity period, the Procuring Agency may request the Bidders’ consent to an extension of the period of validity of their Bids only once through EPADS v2.0, for the period not more than the period of initial bid validity. The Bid Security provided under ITB 18 shall also be suitably extended. A Bidder may refuse the request without forfeiting its Bid security or causing to be executed its Bid Securing Declaration.  A Bidder agreeing to the request will not be required nor permitted to modify its Bid, but will be required to extend the validity of its Bid Security or Bid Securing Declaration for the period of the extension.

18. Bid Security or Bid Securing Declaration

18.1  The Bidder shall furnish as part of its Bid, a Bid Security in accordance with Rule 25 of the Public Procurement Rules, 2004.

18.2  The original Bid Security shall be enclosed within the sealed envelope and to be submitted physically before closing time for submission of bids. Whereas, scanned copy of bid security shall be uploaded electronically through EPADS v2.0 before closing hours for submission of bids.

18.3  The Bidder who failed to submit the original Bids security before the submission deadline shall be disqualified straightaway. 

18.4  The Bid Security or Bid Securing Declaration is required to protect the Procuring Agency against the risk of Bidder’s conduct which would warrant the security’s forfeiture, pursuant to ITB 18.7.

18.5  The Bid Security shall be denominated in the local currency, and it shall be a Bank Draft in the name of the Procuring Agency and valid for twenty-eight (28) days beyond the end of the validity of the Bid. This shall also apply if the period for Bids/Bid Validity is extended. In either case, the form must include the complete name of the Bidder.

18.6  The Bid Security shall be payable promptly upon written demand by the Procuring Agency in case any of the conditions listed in ITB 18 are invoked.

18.7  Unsuccessful Bidders’ Bid Security will be discharged or returned as promptly as possible, however in no case later than thirty (30) days after the expiration of the period of Bids Validity prescribed by the Procuring Agency pursuant to ITB 17. The Procuring Agency shall make no claim to the amount of the Bid Security, and shall promptly return the Bid Security document, after whichever of the following that occurs earliest:

  1. the expiry of the Bid Security;
  2. the entry into force of a procurement contract and the provision of a Performance Guarantee, for the performance of the contract if such a guarantee, is required by the Bid documents;
  3. the rejection by the Procuring Agency of all Bids;
  4. the withdrawal of the Bids prior to the deadline for the submission of Bids, unless the Bids documents stipulate that no such withdrawal is permitted.

18.8  The successful Bidder’s Bids Security will be discharged upon the Bidder signing the contract, or furnishing the Performance Guarantee.

18.9  The Bid Security may be forfeited or the Bid Securing Declaration executed:

  1.  if a Bidder:
  2. withdraws its Bid during the period of Bid Validity as specified by the Procuring Agency, and referred by the Bidder on the Form of Bids except as provided for in ITB 17.2; or
  3. does not accept the correction of errors; or
  4. in the case of a successful Bidder, if the Bidder fails:
  5. to sign the contract; or
  6. to furnish Performance Guarantee.

19. Withdrawal, Substitution, and Modification of Bid

19.1  Before Bid submission deadline, any Bidder may withdraw, substitute, or modify its Bid after it has been submitted through EPADS v2.0. Bids requested to be withdrawn, shall be returned unopened to the Bidders through EPADS v2.0.

20. Format and Signing of Bid

20.1  The Bidder shall prepare and submit Bids with due diligence after carefully reading all the terms and condition before bid submission deadline through EPADS v2.0.

D. Submission of Bids

21.  Submission of Bids through EPADS v2.0

21.1  The Technical and Financial Bids if required to submitted, shall be submitted on EPADS v2.0.  

22. Deadline for Submission of Bids

22.1  Bids shall be received by the Procuring Agency through EPADS v2.0 before bid submission deadline.

22.2  The Procuring Agency may, under exceptional circumstances, extend the deadline for the submission of Bids, after recording reasons in writing and in an equal opportunity manner.   

In such case, all rights and obligations of the Procuring Agency and the Bidders that were previously governed by the original deadline shall thereafter be subject to the revised deadline.

E. Opening and Evaluation of Bids

23. Opening of Bids

23.1  The Bid Evaluation Committee of the Procuring Agency shall open all Bids through the EPADS v2.0, on the date and time specified in the Bid Data Sheet (BDS).

23.2  The Bid Evaluation Committee shall generate minutes through EPADS v2.0 containing brief details of bid opening process. The record of the Bid opening shall include, as a minimum: the name of the Bidder, the Bid price if applicable, and the presence or absence of a Bid Security or Bid Securing Declaration.

23.3  The procuring agency shall live broadcast the opening of bids on national media or on their website or digital channels, if the volume of procurement exceeds five hundred million rupees in case of goods and services and one thousand million rupees in case of works.

23.4  In case the date of opening of bid has been declared as public holiday or the procuring agency fail to open bid due to any EPADS v2.0 related issues, the submission and opening of bids shall be shifted to the next working day on the same time.

23.5  In case of Single Stage One Envelope Procedure, the Bidders names, the Bid prices, the total amount of each Bid and, the presence or absence of Bid Security, Bid Securing Declaration and such other details as the Procuring Agency may consider appropriate, will be announced by the Bid Evaluation Committee.

24. Clarification of Bids

24.1  To assist in the examination, evaluation and comparison of Bids of the Bidders, the Procuring Agency may, ask any Bidder for a clarification of its Bid including breakdown of prices.   

24.2  The request for clarification and the response shall be sought through EPADS v2.0 before three days prior to the deadline for submission of bids. No change in the prices or substance of the Bids shall be sought, offered, or permitted.

24.3  The alteration or modification in the BIDS which in any way affect the following parameters will be considered as a change in the substance of a Bids:

  1. evaluation & qualification criteria;
  2. required scope of work or specifications;
  3. all securities requirements;
  4. tax requirements;
  5. terms and conditions of Bidding documents.
  6. change in the ranking of the Bidder

24.4  From the time of Bids opening to the time of Contract award if any Bidder wishes to contact the Procuring Agency on any matter related to the Bids it should do so through EPADS v2.0.

25. Preliminary Examination of Bids

25.1  Prior to the detailed evaluation of Bids, the Procuring Agency will determine whether each Bid:

  1. meets the eligibility criteria defined in ITB 3;
  2. has been prepared as per the format and contents defined by the Procuring Agency in the Bidding documents;
  3. is accompanied by the required securities; and
  4. is substantially responsive to the requirements of the Bidding documents.

25.2  The Procuring Agency's determination of a Bid's responsiveness will be based on the contents of the Bid itself.

25.3  A substantially responsive Bid is one which conforms to all the terms, conditions, and specifications of the Bidding documents, without material deviation or reservation. A material deviation or reservation is one that: -

  1. affects in any substantial way the scope, quality, or performance of the Goods;
  2. limits in any substantial way, inconsistent with the Bidding documents, the Procuring Agency's rights or the Bidders obligations under the Contract; or
  3. if rectified, would affect unfairly the competitive position of other Bidders presenting substantially responsive Bids.

25.3  If a Bids is not substantially responsive, it will be rejected by the Procuring Agency and may not subsequently be evaluated for complete technical responsiveness.

26. Examination of Terms and Conditions; Technical Evaluation

26.1  The Procuring Agency shall examine the Bids to confirm that all terms and conditions specified in the GCC and the SCC have been accepted by the Bidder without any material deviation or reservation.

26.2  The Procuring Agency shall evaluate the technical aspects of the Bids submitted, to confirm that all requirements specified in Schedule of Requirements and Technical Specifications of the Bidding documents have been met without material deviation or reservation.

26.3  If after the examination of the terms and conditions and the technical evaluation, the Procuring Agency determines that the Bid is not substantially responsive in accordance with ITB 25.2, it shall reject the Bid.

27. Correction of Errors

27.1  Bids determined to be substantially responsive will be checked for any arithmetic errors.  Errors will be corrected as follows: -

  1. if there is a discrepancy between unit prices and the total price that is obtained by multiplying the unit price and quantity, the unit price shall prevail, and the total price shall be corrected, unless in the opinion of the Procuring Agency there is an obvious misplacement of the decimal point in the unit price, in which the total price as quoted shall govern and the unit price shall be corrected;
  2. if there is an error in a total corresponding to the addition or subtraction of sub-totals, the sub-totals shall prevail and the total shall be corrected; and
  3. where there is a discrepancy between the amounts in figures and in words, the amount in words will govern.
  4. Where there is discrepancy between grand total of price schedule and amount mentioned on the Form of Bids, the amount referred in Price Schedule shall be treated as correct subject to elimination of other errors.

27.2  The amount stated in the Bid will, be adjusted by the Procuring Agency in accordance with the above procedure for the correction of errors and, with the concurrence of the Bidder, shall be considered as binding upon the Bidder. If the Bidder does not accept the corrected amount, its Bid will then be rejected, and the Bid Security may be forfeited or the Bids Securing Declaration may be executed.

28. Conversion to Single Currency

28.1  To facilitate evaluation and comparison, the Procuring Agency will convert all Bids prices expressed in the amounts in various currencies in which the Bids prices are payable. For the purposes of comparison of bids quoted in different currencies, the price shall be converted into a single currency specified in the bidding documents. The rate of exchange shall be the selling rate prevailing on the date of opening of financial bids specified in the bidding documents, in accordance with weighted average customer exchange rates list issued by the State Bank of Pakistan on that day.

29. Evaluation of Bids

29.1  The Bids, quotations, or proposals shall be evaluated by the respective evaluation committees as per evaluation criteria described in the Bidding Documents in accordance with Rule 29 and 30 of the Public Procurement Rules, 2004.

1. Least Cost Based Selection (LCBS)
After meeting the requirements of eligibility, qualification and substantial responsiveness, the bid in compliance with all the mandatory (technical) specifications/requirements and/or requisite quality threshold (if any), and having lowest evaluated cost (or financial proposal) shall be considered Successful Bid.

2. Quality and Cost Based Selection (QCBS)
In such combination, there shall be some specific weightage of both the technical features and financial aspects of the proposal. The financial marks shall be awarded on the basis of inverse proportion calculations. The successful bid shall be declared, on the basis of combined evaluation.

3. Quality Based Selection (QBS)
Atter meeting the requirements of eligibility, qualification and substantial responsiveness the bid in compliance with all the mandatory (technical) specifications/requirements and attaining highest marks in the Technical Evaluation considering all other qualitative and/or quantitative parameters (or point rated criteria) for technical proposal(s) such as working methodology, implementation plan, resource allocation, additional functionalities, risk management approach, knowledge transfer techniques, post implementation methodology etc. shall be treated as highest ranked bid. Later on, the financial proposal of highest ranked bidder shall be opened, however, in case of failure to proceed further with such a bidder, the procuring agency may resort to second highest bidder and so on.

29.2  In case of tie of bids, the bidders shall be provided an opportunity to offer their best and final monetary offer through EPADS v2.0. However, in no case the rates shall be higher than the original financial bids.

30. Domestic Preference

30.1  The procuring agency shall evaluate and compare bids, allow for preference to domestic bidders, while competing with the international bidders in accordance with the policies of Federal Government.

The percentage of preference, to be accorded shall be clearly mentioned in the bidding documents under the bid evaluation criteria.

31. Determination of Successful Bid

31.1  Selection technique will be adopted for determining the Successful Bid in accordance with the criteria referred in the BDS or prescribed in the separate section titled as Evaluation Criteria.

31.2  In case where the Procuring Agency adopts the Cost Based Evaluation Technique and, the Bid with the lowest evaluated price from amongst those which are eligible, compliant and substantially responsive shall be the Successful Bid.

31.3  The Procuring Agency may adopt the Quality & Cost Based Selection Technique due to the following two reasons:

1. Where the Procuring Agency knows about the main features, usage and output of the products; however not clear about the complete features, technical specifications and functionalities of the goods to be procured and requires the bidders to submit their proposals defining those features, specifications and functionalities; or

2. Where the Procuring Agency, in addition to the mandatory requirements and mandatory technical specifications, requires parameters specified in Evaluation Criteria to be evaluated while determining the quality of the goods.

31.4  In such cases, the Procuring Agency may allocate certain weightage to these factors as a part of Evaluation Criteria, and may determine the ranking of the bidders on the basis of combined evaluation in accordance with provisions of Rule 2(1)(h) of the Public Procurement Rules, 2004.

32. Abnormally Low Financial Bids

32.1Where the Bid price is considered to be abnormally low, the Procuring Agency shall perform price analysis either during determination of Successful Bids or as a part of the post-qualification process.

32.2  The Procuring Agency may reject an Abnormally low financial bids.

32.3  In order to identify the Abnormally Low Bids (ALB) following approaches can be considered to minimize the scope of subjectivity:

  1. Comparing the Bids price with the cost estimate;
  2. Comparing the Bids price with the Bids offered by other Bidders submitting substantially responsive Bids; and
  3. Comparing the Bids price with prices paid in similar contracts in the recent past either government- or development partner-funded.

32.4  The Procuring Agency will determine to its satisfaction whether the Bidder that is selected as having submitted the successful bid is qualified to perform the contract satisfactorily.

32.5  The determination will take into account the Bidder’s financial, technical, and production capabilities.  It will be based upon an examination of the documentary evidence of the Bidder’s qualifications submitted by the Bidder, as well as such other information as the Procuring Agency deems necessary and appropriate. Factors not included in these Bidding documents shall not be used in the evaluation of the Bidders’ qualifications.

32.6  Procuring Agency may seek “Certificate for Independent Price Determination” from the Bidder and the results of reference checks may be used in determining an award of contract.

Explanation: The Certificate shall be furnished by the Bidder. The Bidder shall certify that the price is determined keeping in view of all the essential aspects such as raw material, its processing, value addition, optimization of resources due to economy of scale, transportation, insurance and margin of profit etc.

32.7  An affirmative determination will be a prerequisite for award of the contract to the Bidder. A negative determination will result in rejection of the Bidder’s Bids, in which event the Procuring Agency will proceed to the next ranked Bidder to make a similar determination of that Bidder’s capabilities to perform satisfactorily.

F. Award of Contract

33. Criteria of Award

33.1 The Procuring Agency will award the Contract to the Bidder whose Bids has been determined to be substantially responsive to the Bidding documents and who has been declared as Most Advantageous Bidder.

34. Negotiations

34.1  The procuring agency shall not engage in negotiations with respect to scope and price with the bidder except when the procuring agency conducts a procurement using direct or negotiated contracting or a request for proposals with evaluation based on quality alone.

34.2  The procuring agency may negotiate with the most advantageous bid with a view to streamline the work or task execution, at the time of contract finalization on methodology, work plan, staffing, finalizing payment arrangements, delivery arrangements, minor amendments to the special conditions of the contract.

35. Procuring Agency Right to reject all bids

35.1  The Procuring Agency reserves the right to reject all bids or proposals at any time prior to the issuance of the Letter of Award, without incurring any liability, in accordance with Rule 33 of the Public Procurement Rules, 2004.

36. Procuring Agency’s Right to Vary Quantities at the Time of Award

36.1  The Procuring Agency reserves the right at the time of contract award to increase or decrease the quantity of Goods originally specified in these Bidding documents provided this does not exceed by 15%, without any change in unit price or other terms and conditions of the Bids and Bidding documents.

37. Notification of Award

37.1  Prior to the award of contract, the procuring agency shall announce and publish the result of bid evaluation on EPADS v2.0 in accordance with Rule 35 of the Public Procurement Rules, 2004.

37.2  The Bidder whose Bids has been accepted will be notified of the award by the Procuring Agency prior to expiration of the Bids/Bid Validity period. The Letter of Award will state the sum that the Procuring Agency will pay the successful Bidder in consideration for the delivery of Goods as prescribed by the Contract (hereinafter and in the Contract called the "Contract Price).

37.3  The Letter of award will constitute the formation of the Contract, subject to the Bidder furnishing the Performance Guarantee and signing of the contract.

38. Signing of Contract

38.1  Promptly after issuance of Letter of award, Procuring Agency shall send the successful Bidder the draft Contract, incorporating all terms and conditions as agreed by the parties to the contract.

38.2  Immediately after the Redressal of grievance by the GRC (if any), mandatory standstill period in accordance with Rule 35 of the Public Procurement Rules, 2004 and after fulfillment of all condition’s precedent of the Contract Form, the successful Bidder and the Procuring Agency shall sign the Contract. 

39. Corrupt & Fraudulent Practices

39.1  Procuring Agencies (including beneficiaries of Government funded projects and procurement) as well as Bidders/Contractors under Government financed contracts, observe the highest standard of ethics during the procurement and execution of such contracts, and will avoid to engage in any corrupt and fraudulent practices. 

F. Grievance Redressal & Complaint Review Mechanism

40. Constitution of Grievance Redressal

40.1  The Grievance Redressal Committee shall address the grievance, if any submitted by any party, including the bidder, in accordance with Rule 48 of the Public Procurement Rules, 2004 to be read with Redressal of Grievances Regulations, 2021.

40.2  In case if any party or the bidder is not satisfied with the decision of the GRC or if it fails to decide within ten days, the bidder or the party may file an appeal before the Appellate Committee of the Authority in accordance with Rule 48 of the Public Procurement Rules, 2004 to be read with Redressal of Grievances Regulations, 2021.

G. Mechanism of Blacklisting

41. Mechanism of Blacklisting

41.1  The Procuring Agency shall initiate blacklisting proceedings against any bidder, supplier, or contractor in accordance with the Mechanism for Blacklisting Regulations, 2024, read with Rule 19 of the Public Procurement Rules, 2004.

41.2  The blacklisted/debarred bidder may file the review petition before the Authority in accordance with Rule 19 of the Public Procurement Rules, 2004 to be read with Procedure of filing and disposal of Review Petitions Regulations, 2021.

📑 Bid Data Sheet (BDS)

Establishment of Online Examination System

Published on: Friday, September 25, 2026 11:00 AM

Ref# : P128944
QR Code

Bids Data Sheet (BDS)

The following specific data for the procurement of Goods to be procured shall complement, supplement, or amend the provisions in the Instructions to Bidders (ITB).  Whenever there is a conflict, the provisions herein shall prevail over those in ITB.

BDS Clause Number
ITB Number
Amendments of, and Supplements to, Clauses in the Instruction to Bidders

A. Introduction

BDS Clause Number 1
ITB Number 1.1

Name of Procuring Agency: Federal Medical College (Federal Medical College)

The subject of procurement is: Establishment of Online Examination System

Expected commencement date: Tuesday, November 17, 2026

BDS Clause Number 2
ITB Number 2.1

Financial year for the operations of the Procuring Agency: 2026-27

Name and identification number of the Contract: P128944 

BDS Clause Number 3
ITB Clause Number 3.1

JV/Consortium or Association Allowed: No
Number of JV/Consortium Members: Nil
see section of eligibility criteria.

B. Bidding Documents

BDS Clause Number 4
ITB Number 8.1

The Bidders may seek clarifications through EPADS v2.0 : Clarification Date: Wednesday, October 14, 2026

C. Preparation of Bids

BDS Clause Number 5
ITB Number 10.1

The Language of all correspondences and documents related to the Bids shall be in: English 

List of documents required along with the bid:

  1. All relevant documents as mentioned in the bid document (uploaded on PPRA Website)

BDS Clause Number 6
ITB Number 11.1
Items/Lots and threre related documents:
See section items and Lots

BDS Clause Number 7
ITB Number 12.1

Items / Lots Specifications:

see section of items specifications.

BDS Clause Number 8
ITB Number 15.6

The price shall be Fixed.

BDS Clause Number 9
ITB Number 16.1

Currency of the Bids shall be : PKR

BDS Clause Number 10
ITB Number 17.1

The Bids/Bid Validity period shall be: 360 Days

BDS Clause Number 11
ITB Number 18.1

The amount of Bid Security shall be as defined in Bid Security Section for items and lots given in BDS 6
The Bid Security shall be in the form of: Pay Order, Demand Draft  

D. Submission of Bids

BDS Clause Number 12
ITB Number 20.1

Bid shall be submitted online on EPADS v2.0 whereas hard copy of the bid security should be submitted to the following;

Federal Medical College, Hanna Road, G-8/4, Islamabad before bid submission deadline.

Bids that are not submitted on EPADS v2.0 shall be disqualified.

The deadline for Bids submission is: Wednesday, October 14, 2026 11:00 AM

E. Opening and Evaluation of Bids

BDS Clause Number 13
ITB Number 23.1

The Bids opening shall take place on EPADS v2.0.

Day : Wednesday

Date: Wednesday, October 14, 2026

Time : 11:30 AM

BDS Clause Number 14
ITB Number 31.1

Selection technique adopted will be: Quality and Cost Based Selection (QCBS)
see Evaluation Criteria

F. Review of Procurement Decisions

BDS Clause Number 15
ITB Number 41.1

Grievence against this procurement shall be submitted online on EPADS v2.0.

Arbitrator shall be appointed by mutual consent of the both parties.

Eligibility Criteria

Bidder's Type Required Registration

Sole Proprietorship

Partnership Firm

Company (Private Limited)

NADRA CITIZENSHIP (CNIC/NICOP)

FBR (NTN)

FBR (GSTN)

Eligibility Criteria Document
The bidder shall conduct a mandatory site survey to examine the existing halls, walls, flooring, ceiling, electrical system, UPS connectivity, network infrastructure, lighting, entrances and workstation locations. (Duly Singed and Stamped attendance sheet from FMC representative) Yes
The tender fee duly signed and stamped receipt amounting PKR 5000/- from the FMC should be attached. Yes
A valid Manufacturer’s Authorization Letter (MAL) for the proposed core switches, access switches, desktop computers, and passive network components must be attached to the technical bid. Failure to submit the required MAL(s) shall result in disqualification. Yes
Bidder MUST provide written acknowledgment on a Stamp Paper of PKR 100 duly attested by the notary public Federal Medical College may visit the warehouse for inspection of the quoted quantities of hardware Ex-Stock. Delivery of hardware/Software / equipment / Installation /Configuration must be within fifteen (15) days from Purchase Order. Yes
Undertaking on the official letterhead that The bidder must submit samples of the quoted solution to FMC before the technical bid opening. Failure to provide the required samples within the specified timeframe shall result in disqualification of the bid. Yes
2 x Certified Resource of the quoted brand. 2 x Certified resource for the existing network switches / XDR / Firewall for the smooth integration and configuration. Yes
The quoted brand must be having service centers in Islamabad/ Rawalpindi. List of service centers need to be attached Yes
The bidder shall be authorized distributor/partner/reseller of OEM. Yes
Affidavit on the Stamp Paper duly attested by Notary Public that the bidder is not blacklisted by any government / semi government / public Department. Yes
Bidder Affidavit on the Stamp Paper attested by Notary Public which certifies to provide One -years warranty/guarantee after installation for IT equipment/software. Yes
Bidder is an Active Taxpayers as per Federal Board of Revenue (FBR)'s database i.e. Active Taxpayers List (ATL) Yes
Bidder has a valid Registration Certificate for Income Tax, Sales Tax and/or other allied agencies / organizations / regulatory authorities Yes
Bidder is an entity duly registered and incorporated under the laws of Pakistan. Bidder has a valid Registration Certificate for Income Tax, Sales Tax and/or other allied agencies / organizations / regulatory authorities Yes
Undertaking on Judicial Paper that the bidder will fulfil all terms and conditions / scope of work requirements mentioned in bid document. Yes
The bidder shall provide comprehensive High-Level Design (HLD) diagram, clearly illustrating connectivity with the existing infrastructure and ensuring seamless integration with the current environment. Yes
The bidder shall provide comprehensive Low-Level Design (LLD) diagram, clearly illustrating connectivity with the existing infrastructure and ensuring seamless integration with the current environment. Yes
Undertaking on official letterhead for Smooth integration of the proposed core and access switches with the existing network infrastructure including firewalls, switches, servers, and other connected devices shall be the sole responsibility of the bidder. The bidder shall also integrate the proposed switches with the existing Network Management System (NMS) for centralized monitoring, management, and log collection. Yes
Undertaking on official letterhead that The bidder shall install and configure the existing XDR solution on all proposed desktops after delivery. The required XDR licenses shall be provided by FMC. The bidder shall also integrate the proposed desktops and XDR solution with the existing firewall and Network Management System (NMS) to enable centralized monitoring, event visibility, and log correlation. Yes
The bidder shall prepare and submit detailed layout drawings showing: o Placement and numbering of all 50 workstations o Desktop computer locations o Electrical and centralized UPS power points o Network/data outlets and cable routes o Distribution boards and protective devices o Cable trays, conduits and trunking o Access routes and circulation spaces o Wall-paneling and painted wall areas Yes
Undertaking on the official letterhead that the Vendor is solely responsible to provide the support services for the offered product even the support for the same product would have been discontinued by the OEM Yes
All Vendors must follow the uploaded Tender documents on PPRA Website for full specification and scope of work No

Evaluation Criteria

Eligibile bidder(s) with substantially responsive bid(s) offering Quality and Cost Based Selection (QCBS) shall be consider for the award of contract(s).

Quality and Cost Based Selection (QCBS)

Weightage

Technical Evaluation %Financial Evaluation %
8020
Technical Marks100
Passing Marks80
Financial Strength of the Company provide Financial statements/ Bank Statement / Annual Turnover of FY 2024-25 and 2025-26
Bidder must provide evidence in the form of audit report or bank statement. (Quantitative)(Doc Required)

  30 million or more (Only Click this option if the firm is eligible for this criteria)   (25)

  20 million to 29 million (Only Click this option if the firm is eligible for this criteria)   (20)

  10 to 19 million (Only Click this option if the firm is eligible for this criteria)   (15)

25
Bidder is an entity duly registered and incorporated under the laws of Pakistan
Bidder is an entity duly registered and incorporated under the laws of Pakistan (Attach Proof) (Quantitative)(Doc Required)

  Three (03) or more year (Only Click this option if the firm is eligible for this criteria)   (25)

  Two (02) to Three (03) years (Only Click this option if the firm is eligible for this criteria)   (15)

  One (01) to two (02) years (Only Click this option if the firm is eligible for this criteria)   (5)

25
Meeting the Delivery Timelines after issuance of P.O.
Bidder MUST provide written acknowledgment on a Stamp Paper of PKR 100 duly attested by the notary public (Federal Medical College may visit the warehouse for inspection of the quoted quantities of hardware Ex-Stock). Delivery time shall be started after the issuance of Purchase Order (PO) (Quantitative)(Doc Required)

  Delivery of hardware/Software equipment within fifteen (15) days or less.   (25)

  Delivery of hardware/Software equipment within twenty (20) days   (10)

  Delivery of hardware/Software equipment within thirty (30) Days   (5)

25
Certified Resource of the quoted brand
Certified Resource of the quoted brand (Quantitative)(Doc Required)

  2-5 certified resources of the quoted brand (Attach a single PDF file)   (25)

  1- 2 certified resources of the quoted brand (Attach a single PDF file)   (10)

25

Items/Lots

Lot Title : Online Examination System

Bid Security : 1000000 PKR

Item UNSPSC Delivery Schedule QuantitySample QuantityManufacturer / Dealer AuthorizationWarranty
Passive Complete Networking Datacom cross connect system and accessories
Address: Federal Medical College, Hanna Road, G-8/4, Islamabad Schedule: 15 Days Quantity: 50/Qty
50 / Qty1 -- 1 Years
Enterprise grade Network Data Switch 48x Gigabit Ports (Layer 2) Network switches
Address: Federal Medical College, Hanna Road, G-8/4, Islamabad Schedule: 15 Days Quantity: 1/Qty
1 / Qty-- Manufacturer Authorization form 1 Years
Enterprise grade Network Data Switch 24x Gigabit Ports (Layer 2) Network switches
Address: Federal Medical College, Hanna Road, G-8/4, Islamabad Schedule: 15 Days Quantity: 1/Qty
1 / Qty-- Manufacturer Authorization form 1 Years
Enterprise grade Network Core Switch, 24x SFP Ports (Layer 3) Network switches
Address: Federal Medical College, Hanna Road, G-8/4, Islamabad Schedule: 15 Days Quantity: 1/Qty
1 / Qty-- Manufacturer Authorization form 1 Years
SFP Transceivers and media converters
Address: Federal Medical College, Hanna Road, G-8/4, Islamabad Schedule: 15 Days Quantity: 8/Qty
8 / Qty1 -- --
Workstations Computer workstation
Address: Federal Medical College, Hanna Road, G-8/4, Islamabad Schedule: 15 Days Quantity: 50/Qty
50 / Qty1 -- 1 Years
Workstation Chairs Office or work chair
Address: Federal Medical College, Hanna Road, G-8/4, Islamabad Schedule: 15 Days Quantity: 50/Qty
50 / Qty1 -- 1 Years
Electrical power points Electrical receptacles
Address: Federal Medical College, Hanna Road, G-8/4, Islamabad Schedule: 15 Days Quantity: 50/Qty
50 / Qty1 -- --
Air Conditioner 1.5 Ton Air conditioners
Address: Federal Medical College, Hanna Road, G-8/4, Islamabad Schedule: 15 Days Quantity: 3/Qty
3 / Qty-- -- 1 Years
650 VA Line-Interactive UPS Uninterruptible power supply UPS
Address: Federal Medical College, Hanna Road, G-8/4, Islamabad Schedule: 15 Days Quantity: 50/Qty
50 / Qty1 -- 1 Years
Wall finishing / painting/ paneling Panels or paneling
Address: Federal Medical College, Hanna Road, G-8/4, Islamabad Schedule: 15 Days Quantity: 1/job
1 / job1 -- --
Desktop Desktop computer
Address: Federal Medical College, Hanna Road, G-8/4, Islamabad Schedule: 15 Days Quantity: 50/Qty
50 / Qty-- Dealer Authorization form 1 Years

Related Services of Goods:

No

Online Examination System

Item UNSPSC Related Services
Passive Complete Networking Datacom cross connect system and accessories I/O, Faceplate, Patch Panel, Cable, Fiber Optic,
SFP Transceivers and media converters Sample
Workstations Computer workstation Complete Set (With FMC Logo and Station Number)
Workstation Chairs Office or work chair Sample
Electrical power points Electrical receptacles Power Cable, Power DB
650 VA Line-Interactive UPS Uninterruptible power supply UPS 1 Unit
Wall finishing / painting/ paneling Panels or paneling Samples

Items/Lot Specification

Lot Title : Online Examination System

Item: Passive Complete Networking

UNSPSC: Datacom cross connect system and accessories

Specifications / Requirements:

Passive Work including ducting, copper/ fiber laying, termination and fluke testing. i. Giga Cable UTP CAT6 ii. CAT 6 Patch Panel iii. CAT6 I/O iv. Faceplate Single / dual Shutter v. Patch Cords CAT 6, 1 meter vi. Optical Distribution Frame. vii. Dura Duct, Pipe and Accessories CAT 6 Cable Cat 6 Cable, UTP, PVC, 4 pairs, 305 meter / Box Gigabit original copper cable Category 6 U/UTP Cable (with cross-shaped separator) offer the possibility to deploy unshielded Category 6/Class E systems when installed with Cat-6 RJ45 Jacks. • Conductor Diameter: AWG 24 (Ø 0.525 +/- 0.015mm) • Insulation Diameter: PE Ø 0.95 +/- 0.05 mm • Cable assemblies: pairs • Sheath material: PVC Mechanical Features: Maximum cable diameter (mm) 5.40 +/- 0.30 Bending Radius (mm) Dynamic (installation) / Static (installed) ≥ 8x outer diameter / ≥ 4x outer diameter Temperature Range In service / Installation, Transport and Storage -20°C +60°C / 0°C +50°C Standards Cables IEC 61156-5 ed. 2 ANSI/TIA 568-C.2 ISO/IEC11801 ed.2 Fire Rating LSZH: IEC 60332-1 PVC: IEC 60332-1 Patch Panel 1U 19” panels must be available to take a minimum of 24 copper fully shuttered jacks. Other connection densities must be available: The panels must be designed for keystone fitting of the fully shuttered jacks/sockets. For efficiency of the termination and performance tool less terminate able keystone jacks must be used. The copper panel panels must have cable management and tie down points (where required) for copper cable. Panels must have the facility to label each fully shuttered socket/jack. CAT6 I/O RJ45 K6 Jack, Cat 6, UTP, Shuttered (tool-less termination), Category 6/Class E system, fully compliant with Category 6 ISO/IEC, EN and TIA standards for hardware performance, confirmed by independent laboratory certifications (Delta, GHMT). The jacks have the following features: • Category 6 UTP • Keystone fixing; • Tool less assembly (mandatory) • Capable of being wired to both 568B and 568A • three cable entry points • Integral shutter/shuttered jack • Jacks must be reusable i.e it must support multiple termination. Applications - IEEE 802.3 1GBASE-T - PoE – IEEE 802.3at Standards - ISO/ IEC 11801 Edition 2, Am 1-2 - ISO/ IEC 60603-7-5 - EN 50173-1 - ANSI/ TIA/ EIA-568-C.2-2009 - IEC 60512-99-001 Faceplate Single non-shuttered U.K. Single Gang Faceplate, 1 port, w/o shutter. 86 x 86 faceplate range can be loaded with Cat-6 UTP I/O to provide the following configurations: • Single gang, 1 port • Single gang, 2 ports Patch Cord Patch cables must be available in either LSOH or PVC jackets.100 Ohm RJ-45 copper patch cords shall be Category 6. Optical Distribution Frame along with supporting accessories Rack mount with sliding tray pre-loaded with SC Duplex couplers Fluke Testing of Copper Nodes & OTDR testing of fiber links. Dura Duct Duct, Pipe and accessories 16x25mm, 16x38mm, 40x40mm, 60x60 ,1 inch pipe etc.- with Adamjee or equivalent ducting and flexible PVC pipe fiber termination unit/ODF

Item: Enterprise grade Network Data Switch 48x Gigabit Ports (Layer 2)

UNSPSC: Network switches

Specifications / Requirements:

Enterprise grade Network Data Switch (L2) 48x Gigabit Ports: General requirements • The Supplier must provide a letter from the manufacturer of equipment confirming the legal delivery to the territory of Pakistan • Switch must be covered with official warranty of the manufacturer on the territory of Pakistan for a period of not less than 3 years • The switch must be equipped with 10/100/1000BaseT ports, not less than 48 • The switch must be equipped with SFP ports, not less than 8 x 10Gb SFP+ uplink ports (includes 2 x Stacking ports) • MACsec-capable • Switch must support fabric technology • The switch must be equipped with out-of-band 10/100BaseT Ethernet port for management • The switch must be able to mount in 19" Rack. Required rackmount kit must be included. • Software upgrades for the next 10 years minimum. Performance • The switching bandwidth must be not less than 256 Gbps • The switch should have non-blocking architecture. All ports must operate on highest possible speed simultaneously • The maximum number of stored MAC addresses in the switching table the switch shall be not less than 32,000 • The routing table of the switch must store not less 16,000 IPv4 routes • The switch must support 6,000 or more Multicast groups Stacking • The switch must support stacking with other families of switches from the same manufacturer and stack bandwidth must be not less than 40Gbps • The failure of any switch in the stack should not cause stack outage more than 20ms. • The switch must support the joint failover configuration with another identical switch to connected devices can use the mechanism for combining multiple physical channels (LAG) to two switches with active simultaneous use of all channels; the recovery Time in case of any link failure between switches should not exceed 50ms. • The failover configuration must be supported for two separate switches and two separate stacks of switches. Ethernet L2 • The switch must support the IEEE family protocols: 802.3: 802.3, 802.3ae, 802.3ab, 802.3z. • The switch must support 802.1ad (Q-in-Q) and Selective Q-in-Q protocols • The switch mush support High Availability Network Protocols with 50ms recovery time in ring topology with RFC 3619 Ethernet Automatic Protection Switching. • The switch must support 802.1w, 802.1s, PVST+ protocols • The switch must support Link Aggregation Group (LAG). Number of ports in one LAG must be not less than 8 • The switch must support the following mechanisms for traffic balancing in LAG: The combination of the MAC addresses of source and destination; The combination of IP addresses of source and destination; The combination of IP addresses of source and destination, and numbers of TCP and UDP port numbers; The combination of IPv6 source and destination and numbers of the protocols of the 4th layer of the OSI model. • The switch must support 802.1AS, 802.1Qav, 802.1Qat, 802.1BA Routing IPv4/IPv6 • The switch must support Policy-based Routing • The switch must support BFD for static routing and dynamic routing protocols OSPFv2/OSPFv3 L2/L3 Multicast • Then switch must support Multicast VLAN registration (MVR) protocol • The switch must support IGMPv1 / v2 / v3 protocols; • The switch must support protocols: IGMPv1 / v2 / v3 snooping (IGMPv1 / v2 / v3 snooping); • The switch must support the protocol PIM Snooping; User authorization and QoS • Each interface for connecting user devices must support at least 8-x hardware queues. • Access control lists that are configured on the switch port must operate at line speed available on port. • The switch must support the IEEE 802.1x protocol. • The switch should provide dynamic assignment of user access policies L2-L4 on ports Management • The switch must support standard SNMP versions 2c and 3, Syslog. • The switch must support NTP • Switch must support on Prem management

Item: Enterprise grade Network Data Switch 24x Gigabit Ports (Layer 2)

UNSPSC: Network switches

Specifications / Requirements:

Enterprise grade Network Data Switch (L2) 24x Gigabit Ports: General requirements • The Supplier must provide a letter from the manufacturer of equipment confirming the legal delivery to the territory of Pakistan • Switch must be covered with official warranty of the manufacturer on the territory of Pakistan for a period of not less than 3 years • The switch must be equipped with 10/100/1000BaseT ports, not less than 24 • The switch must be equipped with SFP ports, not less than 8 x 10Gb SFP+ uplink ports (includes 2 x Stacking ports) • MAC sec-capable • switch must support fabric technology • The switch must be equipped with out-of-band 10/100BaseT Ethernet port for management • The switch must be able to mount in 19" Rack. Required rackmount kit must be included. • Software upgrades for the next 10 years minimum. Performance • The switching bandwidth must be not less than 208 Gbps • The switch should have non-blocking architecture. All ports must operate on highest possible speed simultaneously • The maximum number of stored MAC addresses in the switching table the switch shall be not less than 32,000 • The routing table of the switch must store not less 16,000 IPv4 routes • The switch must support 6,000 or more Multicast groups Stacking • The switch must support stacking with other families of switches from the same manufacturer and stack bandwidth must be not less than 40Gbps • The failure of any switch in the stack should not cause stack outage more than 20ms. • The switch must support the joint failover configuration with another identical switch to connected devices can use the mechanism for combining multiple physical channels (LAG) to two switches with active simultaneous use of all channels; the recovery Time in case of any link failure between switches should not exceed 50ms. • The failover configuration must be supported for two separate switches and two separate stacks of switches. Ethernet L2 • The switch must support the IEEE family protocols: 802.3: 802.3, 802.3ae, 802.3ab, 802.3z. • The switch must support 802.1ad (Q-in-Q) and Selective Q-in-Q protocols • The switch mush support High Availability Network Protocols with 50ms recovery time in ring topology with RFC 3619 Ethernet Automatic Protection Switching. • The switch must support 802.1w, 802.1s, PVST+ protocols • The switch must support Link Aggregation Group (LAG). Number of ports in one LAG must be not less than 8 • The switch must support the following mechanisms for traffic balancing in LAG: The combination of the MAC addresses of source and destination; The combination of IP addresses of source and destination; The combination of IP addresses of source and destination, and numbers of TCP and UDP port numbers; The combination of IPv6 source and destination and numbers of the protocols of the 4th layer of the OSI model. • The switch must support 802.1AS, 802.1Qav, 802.1Qat, 802.1BA Routing IPv4/IPv6 • The switch must support Policy-based Routing • The switch must support BFD for static routing and dynamic routing protocols OSPFv2/OSPFv3 L2/L3 Multicast • Then switch must support Multicast VLAN registration (MVR) protocol • The switch must support IGMPv1 / v2 / v3 protocols; • The switch must support protocols: IGMPv1 / v2 / v3 snooping (IGMPv1 / v2 / v3 snooping); • The switch must support the protocol PIM Snooping; User authorization and QoS • Each interface for connecting user devices must support at least 8-x hardware queues. • Access control lists that are configured on the switch port must operate at line speed available on port. • The switch must support the IEEE 802.1x protocol. • The switch should provide dynamic assignment of user access policies L2-L4 on ports Management • The switch must support standard SNMP versions 2c and 3, Syslog. • The switch must support NTP • Switch must support on Prem management

Item: Enterprise grade Network Core Switch, 24x SFP Ports (Layer 3)

UNSPSC: Network switches

Specifications / Requirements:

Enterprise grade Network Core Switch (L3), 24x SFP Ports General requirements • The Supplier must provide a letter from the manufacturer of equipment confirming the legal delivery to the territory of Pakistan • All equipment must be covered with official guarantee of the manufacturer on the territory of Pakistan for a period of not less than three year • The switch must be equipped with SFP+ ports, not less than 24 • The switch must support up to 2 40Gbit QSFP+ ports • The switch must have 1 expansion slot for additional modules • The switch must be equipped with out-of-band 10/100BaseT Ethernet port for management • The switch must support two or more redundant power supplies that are hot-swappable. • Must support N+1 redundant modular hot-swappable fan units with front to back airflow. • Must support flexible management options to include secure cloud, as well as through an on-premises SNMP management platform, to monitor and manage the device through a supported web browser from anywhere on the network. Please describe the management and on-boarding capabilities of the switch. • Must support industry standard RESTCONF APIs. Please describe supported capabilities for automation and programmability. • The switch must be able to mount in 19" Rack. Required rackmount kit must be included. • Must support both conventional Switched-Routed IP and/or Fabric-based network deployments. Please describe the capabilities of the switch. • Software upgrades for the next 10 years minimum. • Must support the following IP Routing techniques: ‒ Static ‒ RIP/RIPng ‒ OSPFv2/v3 ‒ BGP/BGP+ ‒ VRRP/VRRPv3 ‒ VRF Performance • The switch bandwidth must be not less than 1060 Gbps • The switch should have non-blocking architecture. All ports must operate on highest possible speed simultaneously • The maximum number of stored MAC addresses in the switching table the switch shall be not less than 114,500 • The routing table of the switch must store up to 80,500 of IPv4 routes • The switch must support the up to 43,000 Multicast Entries Stacking • The switch must support stacking with other families switches from the same manufacturer and stack bandwidth must be not less than 200Gb per unit stacking of up to eight witches • The switch must support the joint failover configuration with another identical switch to connected devices can use the mechanism for combining multiple physical channels (LAG) to two switches with active simultaneous use of all channels. • The failover configuration must be supported for two separate switches and two separate stacks of switches. Ethernet L2 • The switch must support the IEEE family protocols: 802.3: 802.3, 802.3ae, 802.3ab, 802.3z. • The switch mush support High Availability Network Protocols with 50ms recovery time in ring topology with RFC 3619 Ethernet Automatic Protection Switching. • The switch must support Link Aggregation Group (LAG). Routing IPv4/IPv6 • Then switch must support following routing protocols: BGP, IS-IS, OSPF, RIP v1/v2, PIM, MSDP • The switch must support Policy-based Routing • The switch must support BFD for static routing and dynamic routing protocols OSPFv2/OSPFv3 BGP L2/L3 Multicast • Then switch must support Multicast VLAN registration (MVR) protocol • The switch must support IGMPv1 / v2 / v3 protocols; • The switch must support protocols: IGMPv1 / v2 / v3 snooping (IGMPv1 / v2 / v3 snooping); • The switch must support the protocol PIM Snooping; User authorization and QoS • Each interface for connecting user devices must support at least 8-x hardware queues. • Access control lists that are configured on the switch port must operate at line speed available on port. • The switch must support the IEEE 802.1x protocol. • Must support the ability to authenticate multiple users on a single port via 802.1X, web, or MAC at the same time. • Must support Denial of Service (DoS) protection. • Switch must support on Prem management

Item: SFP

UNSPSC: Transceivers and media converters

Specifications / Requirements:

10 Gbps

Item: Workstations

UNSPSC: Computer workstation

Specifications / Requirements:

For complete specifications, please follow the uploaded document on PPRA Workstation Modular Office Workstation The bidder shall supply, deliver, install, assemble, align, test and commission modular office workstations in accordance with the following minimum requirements. All components shall be new, unused, factory-finished and suitable for intensive office use. 1. Workstation Top Finished worktop dimensions shall be not less than 30 inches wide × 24 inches deep. Worktop shall be manufactured from minimum 16 mm-thick high-density laminated particle board conforming to recognized international or equivalent quality standards. Board shall resist normal wear, scratches, stains, moisture and heat generated by routine office equipment, with factory-applied decorative laminate or melamine on both surfaces. All exposed edges shall have minimum 1 mm-thick PVC edge banding, machine-applied with hot-melt adhesive, uniform and free from peeling, sharp edges, gaps, visible joints or excess adhesive. Worktop shall be secured through concealed heavy-duty metal brackets and shall not sag, vibrate, move or separate during normal use. At least one durable ABS cable-management grommet/wire cup, approximately 50 mm usable diameter, shall be provided with removable or rotating cover. Worktop shall support a minimum uniformly distributed load of 50 kg without permanent deformation or instability. 2. Partition Frame Each workstation shall include a side partition measuring 24 inches wide × 48 inches high and a front partition measuring 33 inches wide × 48 inches high. Dimensional tolerance shall not exceed ±½ inch, subject to site conditions and FMC’s written approval. Frame shall use extruded aluminium sections with minimum 47 mm face width and minimum 1.2 mm wall thickness. Aluminium shall be straight, corrosion-resistant and free from dents, cracks, bends, burrs and visible manufacturing defects, with durable anodized, powder-coated or approved equivalent finish. Each frame shall include at least one horizontal intermediate support member to improve rigidity and retain the upper and lower panels. Vertical and horizontal members shall be mechanically secured using appropriate connectors, screws and concealed fittings and shall withstand routine use without loosening, twisting or deformation. Exposed outer edges shall be completed with compatible top caps, side seals, end caps and finishing profiles. Exposed screws, sharp edges, open channels and unfinished cuts are prohibited. 3. Upper Partition Panel Upper panel shall incorporate an internal frame of laminated particle-board strips or approved material of equal or superior strength. Both sides shall be covered with minimum 12 mm-thick pin board of sufficient density to retain standard drawing pins securely. Both faces shall be finished with commercial-grade industrial fabric in an FMC-approved colour, texture and pattern. Fabric shall be tightly stretched, uniformly bonded, abrasion-resistant and easy to clean, without wrinkles, loose edges, colour variation, visible adhesive or surface defects. Panel edges shall be fully concealed and securely retained within the aluminium frame. 4. Lower Partition Panel Lower panel shall have an internal frame made from laminated particle-board strips or an equivalent reinforced structure. Both sides shall be covered with minimum 3 mm-thick laminated MDF sheets having factory-laminated, scratch-resistant and washable surfaces. Both faces shall have a consistent FMC-approved colour, grain and finish. Panel shall be adequately reinforced and shall not bend, rattle, detach or deform during normal use; all edges shall remain concealed within the aluminium frame. 5. Central Poles and Partition Connections Adjoining partitions shall be interconnected using 47 mm × 47 mm aluminium central poles or an approved compatible equivalent, with minimum 1.2 mm wall thickness. Partitions shall connect through purpose-built shaped hinges, connectors or locking brackets that maintain alignment and structural stability. Worktops shall attach through heavy-duty, corrosion-resistant metal mounting brackets of appropriate thickness and load-bearing capacity, concealed wherever practicable. Ordinary plastic brackets and weak, improvised or unsuitable connections shall not be accepted. 6. Joints and Finishing Accessories All open ends, corners and intersections shall include purpose-built top-side joint covers, L-joint, T-joint and cross-joint connectors, end/corner caps, base levellers and finishing seals wherever required. The jointing system shall be compatible with the proposed partition profile, securely connect adjoining sections, maintain uniform alignment and eliminate exposed edges, open gaps and sharp corners.

Item: Workstation Chairs

UNSPSC: Office or work chair

Specifications / Requirements:

ParameterMinimum Required Specification
Chair typeErgonomic, high-back revolving office chair suitable for prolonged daily use.
BackrestHigh-back, ergonomically contoured design providing appropriate lumbar and upper-back support.
UpholsteryPremium-quality black leatherette, PU leather or approved equivalent; durable, washable and abrasion-resistant.
SeatHigh-density moulded foam, minimum 50 mm thickness, designed to retain its shape during prolonged use.
Internal structureStrong moulded plywood, engineered wood, polypropylene or equivalent reinforced internal frame.
Seat-height adjustmentPneumatic gas-lift mechanism with adjustable seat height.
Gas liftHeavy-duty Class 3 or better gas-lift cylinder.
Reclining mechanismTilt/reclining mechanism with tension control and upright-position locking facility.
Swivel360-degree smooth revolving mechanism.
ArmrestsTwo fixed, ergonomically shaped and cushioned polypropylene armrests.
BaseHeavy-duty five-star reinforced nylon or powder-coated metal base.
CastorsFive durable twin-wheel nylon castors suitable for tiled and carpeted floors.
Load capacityMinimum 120 kg.
Overall colorBlack, unless otherwise approved by FMC.
WorkmanshipAll edges, joints, stitching and fittings shall have a smooth and durable finish, without sharp edges or manufacturing defects.
AssemblyChair shall be supplied completely assembled or assembled at the designated site by the bidder.
WarrantyMinimum one-year comprehensive warranty covering the gas lift, reclining mechanism, base, castors, frame and manufacturing defects.
Sample requirementBidder must submit a sample of the quoted chair before the technical bid opening for physical inspection and approval by FMC.
Compliance and acceptanceSupplied chairs must be identical to the approved sample. Any inferior, damaged or non-compliant chair shall be rejected and replaced by the bidder at no additional cost to FMC.

Item: Electrical power points

UNSPSC: Electrical receptacles

Specifications / Requirements:

The bidder shall be solely responsible for the complete design, supply, installation, testing, commissioning, and operationalization of fifty (50) electrical power points for the proposed desktop computers at their designated workstations. The scope shall include, but not be limited to: • Installation of complete electrical wiring from the existing main UPS distribution system to each designated workstation. • Provision of suitable power sockets, cables, conduits, trunking, junction boxes, distribution boards, circuit breakers, accessories, and all associated materials required for a complete and operational installation. • Use of original Pakistan Cables, FAST Cables, or an equivalent approved brand of appropriate size and current-carrying capacity. The cable size shall be determined according to the connected load and applicable electrical safety standards. • Each power point shall be clearly labelled as “UPS Power” . • All wiring shall be installed in properly secured PVC conduits or cable trays, or trunking. No loose or exposed wiring shall be permitted. • The bidder shall assess the capacity and availability of the existing UPS system and associated distribution infrastructure before commencing the installation. • The installation shall be completed without disrupting the existing electrical and IT infrastructure. • Any cutting, drilling, wall panelling, painting, finishing, or restoration work required during installation shall be completed by the bidder to the satisfaction of FMC. • The bidder shall perform insulation, polarity, earthing, voltage, load, and operational tests after installation. • The bidder shall submit updated electrical layout drawings, circuit identification, and test reports upon completion. The entire installation shall comply with applicable electrical safety standards and FMC’s requirements. All materials, labour, tools, transportation, testing equipment, accessories, and associated civil works necessary to complete the installation shall be included in the quoted price. No additional payment shall be made for any item required to provide a complete, safe, properly finished, and fully functional centralized UPS power solution.

Item: Air Conditioner 1.5 Ton

UNSPSC: Air conditioners

Specifications / Requirements:

T3 Tropicalized Inverter, Auto Clean Sterilization System, Heat & Cool

Item: 650 VA Line-Interactive UPS

UNSPSC: Uninterruptible power supply UPS

Specifications / Requirements:

For Complete Specifications, Please follow the uploaded document on PPRA Website

Item: Wall finishing / painting/ paneling

UNSPSC: Panels or paneling

Specifications / Requirements:

• The bidder shall inspect all walls and repair cracks, holes, damaged plaster, uneven surfaces, moisture-affected areas and other visible defects before applying any finish. • Existing loose paint, dust, grease and damaged material shall be removed. • Wall surfaces shall be properly scraped, filled, levelled, sanded and prepared using suitable primer, putty and base coats. • Any dismantling, cutting, drilling or minor civil work required for electrical, data, workstation or wall-panelling installation shall be included in the bidder’s scope. • Existing floors, ceilings, doors, windows, equipment and other infrastructure shall be adequately protected throughout the renovation work. Decorative Wall Paneling • Decorative wooden-slat wall panelling, shall be installed on the wall areas identified and approved by FMC. • The bidder shall take exact measurements and submit actual material samples before installation. • The panelling shall comprise durable, uniformly spaced decorative vertical slats fixed over a suitable black backing panel, acoustic-felt backing or approved equivalent substrate. • Slats shall have a laminated, veneered, PVC-wrapped or equivalent wood-finish surface of an FMC-approved colour and texture. • The backing material shall be black, moisture-resistant, dimensionally stable and appropriate for indoor commercial use. • Panels shall be properly aligned, levelled and securely fixed using concealed fasteners or approved adhesive and mechanical-fixing methods. • Visible screws, loose panels, open joints, uneven spacing, chipped edges, exposed cuts or colour variations shall not be accepted. • All internal and external corners, exposed ends, ceiling junctions, floor junctions, electrical outlets and openings shall be finished with matching trims or profiles. • Wall panelling shall not obstruct electrical points, data outlets, ventilation openings, fire-safety equipment, doors, windows or access to existing services. • The bidder shall provide samples of the proposed slat, backing, colour, finish and edge profile for FMC’s approval before bulk installation. Painting Works • Wall areas not covered by decorative panelling shall receive complete surface preparation and premium-quality interior paint. • A minimum of one coat of approved primer and two finishing coats of premium washable emulsion paint shall be applied, or additional coats as required to achieve a uniform finish. • The paint shall be low-odour, low-VOC, washable, fungus-resistant and suitable for high-occupancy office environments. • Colours shall be selected and approved by FMC. • Finished walls shall be uniform and free from brush marks, roller marks, patches, cracks, bubbles, peeling, stains and colour variation.

Item: Desktop

UNSPSC: Desktop computer

Specifications / Requirements:

PERFORMANCE__EMPTY
ProcessorIntel Core™ Ultra 5 225, 10C (6P + 4E) / 10T, Max Turbo up to 4.9GHz, 20MB Intel® Smart Cache
AI PC CategoryAI PC
Memory1x 16GB UDIMM DDR5-5600
Memory SlotsTwo DDR5 UDIMM slots, dual-channel capable
Max MemoryUp to 64GB DDR5-5600
Storage512GB SSD M.2 2280 PCIe® 4.0x4 NVMe®
Card Reader3-in-1 Card Reader
OpticalNone
Audio ChipHigh Definition (HD) Audio, Realtek® ALC623-CG codec
Speakers2Wx1
Power Supply200W 90%
DESIGN 
LED21.5 Inch Monitor with HDMI
KeyboardUSB, Calliope, Black, English (UK)
MouseUSB Calliope Mouse, Black
Optional Bay3.5" HDD Bracket
Case ColorBlack
System FanNone
Toolless Chassis ScrewToolless Chassis Screw
PenPen Not Supported
Form FactorTower
CONNECTIVITY 
WLAN + BluetoothIntel® Wi-Fi® 6 AX203, 802.11ax 2x2 + BT5.2
EthernetRTL8111K, 1x RJ-45
Front Ports1x USB-C® (USB 5Gbps / USB 3.2 Gen 1), with data transfer and 15W charging, 2x USB-A (Hi-Speed USB / USB 2.0), 2x USB-A (USB 5Gbps / USB 3.2 Gen 1), 1x headphone / microphone combo jack (3.5mm), 1x microphone (3.5mm)
Rear Ports2x USB-A (Hi-Speed USB / USB 2.0), 2x USB-A (USB 5Gbps / USB 3.2 Gen 1), one supports Smart Power On, 1x HDMI® 2.1 TMDS, 1x DisplayPort™ 1.4, 1x VGA, 1x Ethernet (RJ-45), 1x line-out (3.5mm)
SECURITY & PRIVACY 
Security ChipDiscrete TPM 2.0, TCG certified, FIPS 140-2 certified
Physical LocksKensington Security Slot™, 3 x 7 mm, Padlock Loop
Chassis Intrusion SwitchChassis Intrusion Switch
SERVICE 
Base Warranty1-year, Courier or Carry-in
Operation SystemWindows 11 Pro

Price Schedule

For Individual Items

# Item Title Quantity Unit Price (PKR) Total Price (PKR) Delivery Location Delivery Period / Year Country of Origin
1
2
For Lots
# Lot Title Total Lot Price (PKR) Country of Origin
1 [Lot 1 Title]

📑 General Conditions of Contract (GCC)

Establishment of Online Examination System

Published on: Friday, September 25, 2026 11:00 AM

Ref# : P128944
QR Code

A. General

1. Definitions

1.1 Unless the context otherwise requires, the following terms whenever used in this Contract shall have the same meaning and shall be interpreted as indicated
  1. “Applicable Law” means the laws and any other instruments having the force of law in the Government’s Country, or in such other country as may be specified in the Special Conditions of the Contract (SC), as they may be issued and in force from time to time;
  2. “Procuring Agency” means:-
    1. any Ministry, Division, Department or any Office of the Government;
    2. any authority, corporation, body or organization established by or under a Law or which is owned or controlled by the Government;.
  3. “The Contract” means an agreement enforceable by law;
  4. “The Contract Price” means the price payable to the Bidder under the Contract for the full and proper performance of its contractual obligations;
  5. “Ancillary Services” means those services ancillary to the provision  of Goods, such as transportation and insurance, and any other incidental services, such as installation, commissioning, provision of technical assistance, training, and other such obligations of the Bidder covered under the  Contract;
  6. “GCC” means the General Conditions of Contract contained in this section;
  7. “SCC” means the Special Conditions of Contract by which the GCC may be amended or supplemented;
  8. “Day” means calendar day unless indicated otherwise.
  9. “Effective Date” means the date on which this Contract comes into force and effect.
  10. The Bidder” means the individual or corporate body whose Bids to provide the Goods has been accepted by the Procuring Agency;
  11. “The Project Site,” where applicable, means the place or places named in Bids Data Sheet and technical Specifications;
  12. “Government” means the Government of Pakistan;
  13. “Subcontractor” means any entity to which the Bidder subcontracts any part of the Goods.
  14.  "Service" means any object of procurement other than goods or works;
  15. “Party” means the Procuring Agency or the Bidder, as the case may be, and “Parties” means both of them;
  16. “Foreign Currency” means any currency other than the currency of the country of the Procuring Agency;
  17. “Completion Date” means the date of completion of the contract by the Bidder as certified by the Procuring Agency;
  18.  “In Writing” means communicated in written form with proof of receipt;
  19. “Local Currency” means the currency of Pakistan;

2. Application and Interpretation

2.1 These General Conditions shall apply to the extent that they are not superseded by provisions of other parts of the Contract.

2.2 In interpreting these Conditions of Contract headings and marginal notes are used for convenience only and shall not affect         their interpretations unless specifically stated; references to singular include the plural and vice versa; and masculine include the feminine. Words have their ordinary meaning         under the   language   of   the   Contract   unless specifically defined.

3. Applicable Law

3.1 The contract shall be governed and interpreted in accordance with the laws of Pakistan, unless otherwise specified in SCC.

4. Governing Language

4.1 The Contract as well as all correspondence and documents relating to the Contract exchanged between the Bidder and the Procuring Agency, shall be written in the English language unless otherwise stated in the SCC.  Supporting documents and printed literature that are part of the Contract may be in another language provided these are accompanied by an accurate translation of the relevant passages in English, in which case, for purposes of interpretation of the Contract, this translation shall govern.

5. Notices

5.1 Any notice, request, or consent made pursuant to this Contract shall be in writing and shall be deemed to have been made when delivered in person to an authorized representative of the Party to whom the communication is addressed, or when sent by registered mail, telex, telegram, or facsimile to such Party at the address specified in the SCC.

6. Delivery/Location

6.1 The Goods shall be delivered to such locations as the Procuring Agency may approve and as specified in SCC.

7. Authorized Representatives / Authority of Member in charge

7.1 Any action required or permitted to be taken, and any document required or permitted to be executed, under this Contract by the Procuring Agency or the Bidder may be taken or executed by the officials specified in the SCC.

B. Commencement, Completion, Modification, and Termination of Contract

8. Effectiveness of Contract

8.1 This Contract shall come into effect on the date the Contract is signed by both parties and such other later date as may be stated in the SCC.

9. Commencement of Services

9.1 The Bidder shall confirm availability of Key Experts and begin carrying out the Services not later than the number of days after the Effective Date specified in the SCC.

10. Program

10.1 Before commencement of the Services, the Bidder shall submit to the Procuring Agency for approval a Program showing the general methods, arrangements, order and timing for all activities. The Services shall be carried out in accordance with the approved Program as updated.

11. Starting Date/Expiration Date

11.1 The Bidder shall start carrying out the Services Five (05) days after the date the Contract becomes effective, or at such other date as may be specified in the SCC.

11.2 Unless terminated earlier pursuant to Clause GCC 15 hereof, this Contract shall expire at the end of such time period after the Effective Date as specified in the SCC.

12. Entire Agreement

12.1 This Contract contains all covenants, stipulations and provisions agreed by the Parties.  No agent or representative of either Party has authority to make, and the Parties shall not be bound by or be liable for, any statement, representation, promise or agreement not set forth herein.

13. Modification

13.1 Any modification or variation of the terms and conditions of this Contract, including any modification or variation of the scope of the Services, may only be made by written agreement between the Parties. However, each Party shall give due consideration to any Bids for modification or variation made by the other Party.

13.2 In cases of any modifications or variations, the prior written consent of the Procuring Agency is required.

14. Force Majeure

14.1 Definition

For the purposes of this Contract, “Force Majeure” means an event which is beyond the reasonable control of a Party and which makes a Party’s performance of its obligations under the Contract impossible or so impractical as to be considered impossible under the circumstances.

14.2 No Breach of Contract

The failure of a Party to fulfill any of its obligations under the contract shall not be considered to be a breach of, or default under, this Contract in so far as such inability arises from an event of Force Majeure, provided that the Party affected by such an event (a) has taken all reasonable precautions, due care and reasonable alternative measures in order to carry out the terms and conditions of this Contract, and (b) has informed the other Party as soon as possible about the occurrence of such an event.

14.3 Extension of Time

Any period within which a Party shall, pursuant to this Contract, complete any action or task, shall be extended for a period equal to the time during which such Party was unable to perform such action as a result of Force Majeure.

14.4 Payments

During the period of their inability to perform the Services as a result of an event of Force Majeure, the Bidder shall be entitled to continue to be paid under the terms of this Contract, as well as to be reimbursed for additional costs reasonably and necessarily incurred by them during such period for the purposes of the Services and in reactivating the Service after the end of such period.

15. Termination

15.1 By the Procuring Agency

The Procuring Agency may terminate this Contract in case of the occurrence of any of the events specified in paragraphs (a) through (e) of this Clause. In such an occurrence the Procuring Agency shall give at least thirty (30) calendar days’ written notice of termination to the Bidder in case of the events referred to in (a) through (d); at least sixty (60) calendar days’ written notice in case of the event referred to in (e);

  1. If the Bidder fails to remedy a failure in the performance of its obligations hereunder, as specified in a notice of suspension;
  2. If the Bidder becomes (or, if the Bidder consists of more than one entity, if any of its members becomes) insolvent or bankrupt or enter into any agreements with their creditors for relief of debt or take advantage of any law for the benefit of debtors or go into liquidation or receivership whether compulsory or voluntary;
  3. If the Bidder fails to comply with any final decision reached as a result of arbitration proceedings;
  4. If, as the result of Force Majeure, the Bidder is unable to perform a material portion of the Services for a period of not less than sixty (60) calendar days;
  5. If the Procuring Agency, in its sole discretion and for any reason whatsoever, decides to terminate this Contract;

15.2 By the Bidder

The Bidder may terminate this Contract, by not less than thirty (30) calendar days’ written notice to the Procuring Agency, in case of the occurrence of any of the events specified in paragraphs (a) through (d) of this Clause.

  1. If the Procuring Agency fails to pay any money due to the Bidder pursuant to this Contract and not subject to dispute within forty-five (45) calendar days after receiving written notice from the Bidder  that such payment is overdue.
  2. If, as the result of Force Majeure, the Bidder is unable to perform a material portion of the Services for a period of not less than sixty (60) calendar days.
  3. If the Procuring Agency fails to comply with any final decision reached as a result of arbitration.
  4. If the Procuring Agency is in material breach of its obligations pursuant to this Contract and has not remedied the same within forty-five (45) days (or such longer period as the Bidder may have subsequently approved in writing) following the receipt by the Procuring Agency of the Bidder’s notice specifying such breach.

C.  Obligations of the Bidder

16. General

16.1 Standard of Performance

  1. The Bidder shall deliver the product and carry out the Services with all due diligence, efficiency and economy, in accordance with generally accepted professional standards and practices, and shall observe sound management practices, and employ appropriate technology and safe and effective equipment, machinery, materials and methods. The Bidder shall always act, in respect of any matter relating to this Contract or to the Services, as a faithful adviser to the Procuring Agency, and shall at all times support and safeguard the Procuring Agency’s legitimate interests in any dealings with the third parties.

16.2 Law Applicable to Goods

The Bidder shall deliver the goods in accordance with the Contract and in accordance with the Law of Pakistan and shall take all practicable steps to ensure that any of its Experts and Sub-Bidders, comply with the Applicable Law. 

17. Conflict of Interests

17.1 Bidder Not to Benefit from Commissions and Discounts.

The remuneration of the Bidder shall constitute the Bidder’s sole remuneration in connection with this Contract or the Services, and the Bidder shall not accept for their own benefit any trade commission, discount, or similar payment in connection with activities pursuant to this Contract or to the Services or in the discharge of their obligations under the Contract, and the Bidder shall use their best efforts to ensure that the Personnel, any Subcontractors, and agents of either of them similarly shall not receive any such additional remuneration.

17.2  Bidder and Affiliates Not to be Otherwise Interested in Project

The Bidder agree that, during the term of this Contract and after its termination, the Bidder and its affiliates, as well as any Subcontractor and any of its affiliates, shall be disqualified from providing Goods for any project resulting from or closely related to the Services.

17.3  Prohibition of Conflicting Activities

Neither the Bidder nor its Subcontractors nor the Personnel shall engage, either directly or indirectly, in any of the following activities:

  1. during the term of this Contract, any business or professional activities in the Government’s country which would conflict with the activities assigned to them under this Contract;
  2. during the term of this Contract, neither the Bidder nor their Subcontractors shall hire public employees in active duty or on any type of leave, to perform any activity under this Contract;

18. Confidentiality

18.1 Except with the prior written consent of the Procuring Agency, the Bidder and the Experts shall not at any time communicate to any person or entity any confidential information acquired in the course of the contract.

19. Insurance to be Taken Out by the Bidder

19.1 The Bidder(a) shall take out and maintain, and shall cause any Subcontractors to take out and maintain, at its (or the Subcontractors’, as the case may be) own cost but on terms and conditions approved by the Procuring Agency, insurance against the risks, loss or damage, and for the coverage, as shall be specified in the SCC; and (b) at the Procuring Agency’s request, shall provide evidence to the Procuring Agency showing that such insurance has been taken out and maintained and that the current premiums have been paid.

20. Bidder’s Actions Requiring Procuring Agency’s Prior Approval

20.1 The Bidder shall obtain the Procuring Agency’s prior approval in writing before taking any of the following actions:

(a)    appointing such members of the Personnel not provided by the Bidder;

(b)    changing the Program of activities; and

(c)     any other action that may be specified in the SCC.

21. Reporting Obligations

21.1 The Bidder shall submit to the Procuring Agency the reports and documents in the numbers, and within the periods as prescribed by the Procuring Agency.

22. Liquidated Damages

22.1  If the Supplier fails to deliver any or all of the Goods or to perform the Services within the period(s) specified in the Contract, the Procuring Agency shall, without prejudice to its other remedies under the Contract, deduct from the Contract Price, as liquidated damages, a sum equivalent to the percentage specified in SCC of the delivered price of the delayed Goods or unperformed Services for each week or part thereof of delay until actual delivery or performance, up to a maximum deduction of the performance security (or guarantee) specified in SCC. Once the said maximum is reached, the Procuring Agency may consider termination of the Contract pursuant to GCC Clause 15.

22.2  Correction for Over-payment

If the Intended Completion Date is extended after liquidated damages have been paid, the Procuring Agency shall correct any overpayment of liquidated damages by the Bidder by adjusting the next payment certificate.  The Bidder shall be paid interest on the overpayment, calculated from the date of payment to the date of repayment, at the rates specified in SCC.

22.3  Lack of performance penalty

If the Bidder has not corrected a Defect within the time specified in the Procuring Agency’s notice, a penalty for Lack of performance will be paid by the Bidder. The amount to be paid will be calculated as a percentage of the cost of having the Defect corrected, assessed as specified in the SCC.

23. Performance Guarantee

23.1 Within Seven (07) days from the issuance of acceptance letter from the Procuring Agency, the successful Bidder shall furnish the Performance Guarantee in shape of ------- at the discretion of the PA in the amount specified in SCC. In case the amount of   Bids security is equal or greater than

23.2 The proceeds of the Performance Guarantee shall be payable to the Procuring agency as compensation for any loss resulting from the Supplier’s failure to complete its obligations under the Contract.

23.3 The Performance Guarantee shall be denominated in the currency of the Contract, or in a freely convertible currency acceptable to the Procuring agency and shall be in the acceptable form as specified in SCC.

23.4 The Performance Guarantee will be discharged by the Procuring agency and returned to the Supplier not later than thirty (30) days following the date of completion of the Supplier’s performance obligations under the Contract, including any warranty obligations, unless otherwise specified in SCC.

24. Fraud and Corruption

24.1 The Procuring Agency requires the Supplier to disclose any commissions or fees that may have been paid or are to be paid to agents or any other party with respect to the Bidding process or execution of the Contract. The information disclosed must include at least the name and address of the agent or other party, the amount and currency, and the purpose of the commission, gratuity or fee.

25. Sustainable Procurement

25.1 The Bidder shall conform to the sustainable procurement contractual provisions, if and as specified in the SCC.

D. Bidder’s Personnel

26. Description of Personnel

26.1 The titles, agreed job descriptions, minimum qualifications, and estimated periods of engagement in the carrying out of the Services of the Bidder’s Key Personnel.  The Key Personnel listed by title as well as by name are hereby approved by the Procuring Agency.

27. Removal and/or Replacement of Personnel

27.1 Except as the Procuring Agency may otherwise agree, no changes shall be made in the Key Personnel.  If, for any reason beyond the reasonable control of the Bidder, it becomes necessary to replace any of the Key Personnel, the Bidder shall provide as a replacement a person of equivalent or better qualifications.

27.2 If the Procuring Agency finds that any of the Personnel have (i) committed serious misconduct or have been charged with having committed a criminal action, or (ii) have reasonable cause to be dissatisfied with the performance of any of the Personnel, then the Bidder shall, at the Procuring Agency’s written request specifying the grounds thereof, provide as a replacement a person with qualifications and experience acceptable to the Procuring Agency.

27.3 The Bidder shall have no claim for additional costs arising out of or incidental to any removal and/or replacement of Personnel.

E.  Obligations of the Procuring Agency

28. Assistance and Exemptions

28.1 The Procuring Agency shall use its best efforts to ensure that the Government shall provide the Bidder such assistance and exemptions as specified in the SCC.

29. Change in the Applicable Law

29.1 If, after the date of this Contract, there is any change in the Applicable Law with respect to taxes and duties which increases or decreases the cost of the related Services rendered by the Bidder, then the remuneration and reimbursable expenses otherwise payable to the Bidder under this Contract shall be increased or decreased accordingly by agreement between the Parties, and corresponding adjustments shall be made to the amounts referred in the SCC.

30. Services and Facilities

30.1 The Procuring Agency shall make available to the Bidder and the Experts, for the purposes of the Services and free of any charge, the services, facilities and property described , at the times and in the manner specified in the SCC or terms of reference.

30.2 In case that such services, facilities and property shall not be made available to the Bidder, the Parties shall agree on (i) any time extension that it may be appropriate to grant to the Bidder for the performance of the Services, (ii) the manner in which the Bidder shall procure any such services, facilities and property from other sources, and (iii) the additional payments, if any, to be made to the Bidder as a result thereof.

F. Payments to the Bidder

31. Contract Price

31.1 The price payable shall be in Pakistani Rupees unless otherwise specified in the SCC. Prices charged by the Supplier for Goods delivered under the Contract shall not vary from the prices quoted by the Supplier in its Bid.

32. Terms and Conditions of Payment

32.1 Payments will be made to the Bidder according to the payment schedule stated in the SCC and as per actual invoice submitted by the Bidder.

32.2 Unless otherwise stated in the SCC, the advance payment shall be made against the provision by the Bidder of a bank guarantee for the same amount, and shall be valid for the period stated in the SCC.  Any other payment shall be made after the conditions listed in the SCC for such payment have been met, and the Bidder have submitted an invoice to the Procuring Agency specifying the amount due.

33. Currency of Payment

33.1 Any payment under this Contract shall be made in the currency(ies) specified in the SCC.

G. Quality Control

34. Identifying Defects

34.1 The principle and modalities of Inspection of the Goods by the Procuring Agency shall be as indicated in the SCC. The Procuring Agency shall check the Bidder’s performance and notify him of any Defects that are found.  Such checking shall not affect the Bidder’s responsibilities.  The Procuring Agency may instruct the Bidder to search for a Defect and to uncover and test any service that the Procuring Agency considers may have a Defect. Defect Liability Period is as defined in the SCC.

35. Correction of Defects,and

Lack of Performance Penalty

35.1 The Procuring Agency shall give notice to the Bidder of any Defects before the end of the Contract.  The Defects liability period shall be extended for as long as Defects remain to be corrected.

35.2 Every time notice a Defect is given, the Bidder shall correct the notified Defect within the length of time specified by the Procuring Agency’s notice.

35.3 If the Bidder has not corrected a Defect within the time specified in the Procuring Agency’s notice, the Procuring Agency will assess the cost of having the Defect corrected, the Bidder will pay this amount, and a Penalty for Lack of Performance.

36. Taxes and Duties

36.1 A Supplier shall be entirely responsible for all taxes, duties, fees, etc., incurred until delivery of the contracted Goods to the Procuring Agency.

H. Settlement of Disputes

37. Alternate Dispute Resolution

37.1 The disputes between the parties to the contract may be settled in accordance with Public Procurement Rules, 2004.

37.2 The procuring agency shall refer the matter to the Chief Justice Islamabad High Court or Managing Director PPRA or the Secretary Ministry of Law & Justice for appointment of Arbitrator.

37.3 The fee for the Arbitrator shall be specified in Pak Rupees as determined by the appointing authority which shall be borne and shared equally by the contracting parties.

📑 Special Conditions of Contract (SCC)

Establishment of Online Examination System

Published on: Friday, September 25, 2026 11:00 AM

Ref# : P128944
QR Code

SECTION VIII. SPECIAL CONDITIONS OF CONTRACT

The following Special Conditions of Contract shall supplement the General Conditions of Contract. Whenever there is a conflict, the provisions herein shall prevail over those in the Conditions of Contract. The corresponding clause number of the GCC is indicated in parentheses.

Number of GC Clause

Amendments of, and Supplements to, Clauses in the General Conditions of Contract

Number of GC Clause 1

Definitions

The Procuring Agency is: Federal Medical College (Federal Medical College), IT Assistant Federal Medical College, Hanna Road, G-8/4, Islamabad

The Supplier is:

The title of the subject procurement is: Establishment of Online Examination System

Number of GC Clause 3

Applicable/Governing Law:

The Contract shall be interpreted in accordance with the laws of Islamic Republic of Pakistan

Number of GC Clause 4

Language:

The language of the Contract, all correspondence and communications to be given, and all other documentation to be prepared and supplied under the Contract shall be in English.

Number of GC Clause 5

Notices:

The addresses for the notices are:

Procuring Agency: 

Federal Medical College (Federal Medical College), IT Assistant
Federal Medical College, Hanna Road, G-8/4, Islamabad
+92-333-525196
info@fmcisb.edu.pk

Contractor/ Bidder: 

 [Name, address and telephone number].

The Contractor/ Bidder’s Representative(s)

[Name, address, telephone number and e-mail address]

Number of GC Clause 7.1

The Authorized Representatives are:

For the Procuring Agency:

Federal Medical College (Federal Medical College), IT Assistant
Federal Medical College, Hanna Road, G-8/4, Islamabad
+92-333-525196
info@fmcisb.edu.pk

For the Bidder:

Name: ………………………

Designation: ……………..

Address: ……………………………..

Number of GC Clause 8

Effectiveness of the contract

Number of GC Clause 9

Commencement of Contract:

Number of GC Clause 11.2

Expiration of Contract:

Number of GC Clause 15

Termination

In the event of termination of the contract due to any reason as already defined in the General Conditions of Contract, the Bidder shall be responsible for providing to the Authority the Goods till the time of alternate arrangements.

Number of GC Clause 17

Conflict of Interest:

The Procuring Agency reserves the right to determine on a case-by-case basis whether the Bidder should be disqualified from providing goods or services due to a conflict of a nature described in Clause GCC 17.

Number of GC Clause 22

Liquidated Damages 

If the Bidder fails to provide services as required under the contract or in case of any data loss/data breach or any incident compromising the data security or other such failures related to any services, the Bidder shall pay to the Procuring Agency as Liquidated Damages at a rate of 1.00% to 1.00% of the Contract value, in accordance with the extent of performance failure & the cost of investigating such incidents as judged by the Authority.

Number of GC Clause 23

Performance Guarantee:

The amount of performance guarantee shall be 2.00% of the contract price in acceptable form of Pay Order, Bank Guarantee, Demand Draft

Number of GC Clause 32

Payment terms:

Payment will be made to the Bidder against the procured Goods and services according to the actual invoice or running bills submitted by the Bidder against the services provided within the time given in the conditions of the contract.

Number of GC Clause 33

Currency of Payment:

All the payment to be released to the contractor/Bidder shall be in Pakistani Rupees.

Number of GC Clause 34

Identifying Defects:

The Authority reserves the right at any time to inspect the premises of the provider to inspect the goods and monitor the goods being provided.

Number of GC Clause 37

Following is the guidance for Dispute Resolution

  1. If any dispute of any kind whatsoever shall arise between the Authority and the Bidder in connection with or arising out of the Contract, including without prejudice to the generality of foregoing, any question regarding its existence, validity, termination and the execution of the Contract – whether during developing phase or after their completion and whether before or after the termination, abandonment or breach of the Contract – the parties shall seek to resolve any such dispute or difference by mutual diligent negotiations in good faith within 14 (fourteen) days following a notice sent by one Party to the other Party in this regard.
  2. At future of negotiation the dispute shall be resolved through mediation and mediator shall be appointed with the mutual consent of the both parties.
  3. At the event of failure of mediation to resolve the dispute relating to this contract such dispute shall finally be resolved through binding Arbitration by sole arbitrator in accordance with Arbitration Act 1940. The arbitrator shall be appointed by mutual consent of the both parties. The Arbitration shall take place in Islamabad, Pakistan and proceedings will be conducted in English language. 
  4. The cost of the mediation and arbitration shall be shared by the parties in equal proportion however the both parties shall bear their own costs and lawyer’s fees regarding their own participation in the mediation and arbitration. However, the Arbitrator may make an award of costs upon the conclusion of the arbitration making any party to the dispute liable to pay the costs of another party to the dispute.
  5. Arbitration proceedings as mentioned in the above clause regarding resolution of disputes may be commenced prior to, during or after completion of the contract.

Notwithstanding any reference to the arbitration herein, the parties shall continue to perform their respective obligations under the Contract unless they otherwise agree that the Authority shall pay the Bidder any monies due to the Bidder.

Rules of procedure for arbitration proceedings: 

Any dispute between the Authority and a Bidder who is a national of the Islamic Republic of Pakistan arising in connection with the present Contract shall be referred to adjudication or arbitration in accordance with the laws of the Islamic Republic of Pakistan including Arbitration Act 1940, however above provision shall prevail in referring the case to the Arbitrator.

Place of Arbitration and Award:

The arbitration shall be conducted in English language and place of arbitration shall be at Islamabad. The award of the arbitrator shall be final and shall be binding on the parties.

📑 Bid Securing Declaration (BSD)

Establishment of Online Examination System

Published on: Friday, September 25, 2026 11:00 AM

Ref# : P128944
QR Code

Form 9: Bid Securing Declaration

Date: [insert date (as day, month and year)]

Bid No.:P128944

To: Federal Medical College (Federal Medical College), IT Assistant Federal Medical College, Hanna Road, G-8/4, Islamabad

 

 

We, the undersigned, declare that:

We understand that, according to your conditions, Bids must be supported by a Bid Securing Declaration.

We accept that we will be blacklisted and henceforth cross debarred  for participating in respective category of public procurement proceedings for a period of (not more than) six months, if fail to abide with a bid securing declaration, however without indulging in corrupt and fraudulent practices, if we are in breach of our obligation(s) under the Bid conditions, because we:

  1. have  withdrawn  or  modified  our  Bid  during  the  period  of  Bid  Validity specified in the Form of Bid;
  2. Disagreement to arithmetical correction made to the Bid price; or
  3. having been notified of the acceptance of our Bid by the Procuring Agency during the period of Bid Validity, (i) failure to sign the contract if required by Procuring Agency to do so or (ii) fail or refuse to furnish the Performance Security or to comply with any other condition precedent to signing the contract specified in the Bidding Documents.

We understand this Bid Securing Declaration shall expire if we are not the successful

Bidder, upon the earlier of (i) our receipt of your notification to us of the name of the successful Bidder; or (ii) twenty-eight (28) days after the expiration of our Bid.

 

📑 Contract Form (CNF)

Establishment of Online Examination System

Published on: Friday, September 25, 2026 11:00 AM

Ref# : P128944
QR Code

SECTION IX: CONTRACT FORMS

 

THIS AGREEMENT made the _____ day of __________ 20_____ between Federal Medical College (Federal Medical College), IT Assistant Federal Medical College, Hanna Road, G-8/4, Islamabad

 (hereinafter called “the Procuring Agency”) of the one part and [name of Bidder] of [city and country of Bidder] (hereinafter called “the Bidder”) of the other part:

 

WHEREAS the Procuring Agency invited Bids for provision of goods, viz., Establishment of Online Examination System (P128944) and has accepted a Bids by the Bidder for the provision of Goods in the sum of [contract price in words and figures] (hereinafter called “the Contract Price”).

 

NOW THIS CONTRACT WITNESSETH AS FOLLOWS:

 

1.   In this Contract words and expressions shall have the same meanings as are respectively assigned to them in the Conditions of Contract referred to.

2.   The following documents shall be deemed to form and be read and construed as part of this Contract, In the event of any ambiguity or conflict between the Contract Documents listed below, the order of precedence shall be the order in which the Contract Documents are listed below:-

  1. This form of Contract;
  2. the Form of Bids and the Price Schedule submitted by the Bidder;
  3. the Schedule of Requirements;
  4. the Technical Specifications;
  5. the Special Conditions of Contract;
  6. the General Conditions of the Contract;
  7. the Procuring Agency’s Letter of Acceptance; and
  8. [add here: any other documents]

3.   In consideration of the payments to be made by the Procuring Agency to the Bidder as hereinafter mentioned, the Bidder hereby covenants with the Procuring Agency to provide the Goods related services and to remedy defects therein in conformity in all respects with the provisions of the Contract.

4.   The Procuring Agency hereby covenants to pay the Bidder in consideration of the provision of Goods and the remedying of defects therein, the Contract Price or such other sum as may become payable under the provisions of the contract at the times and in the manner prescribed by the contract.

 

IN WITNESS whereof the parties hereto have caused this Contract to be executed in accordance with their respective laws the day and year first above written.

 

Signed, sealed, delivered by __________________the ________________ (for the Procuring Agency)

 

Witness to the signatures of the Procuring Agency:

………………………………………………

Signed, sealed, delivered by __________________the ________________ (for the Procuring Agency)

 

Witness to the signatures of the Bidder: …………………………………………………

 

 

📑 Integrity Pact (INP)

Establishment of Online Examination System

Published on: Friday, September 25, 2026 11:00 AM

Ref# : P128944
QR Code

Integrity Pact

DECLARATION OF FEES, COMMISSION AND BROKERAGE ETC. PAYABLE BYTHE SUPPLIERS OF GOODS, SERVICES & WORKS IN  CONTRACTS WORTH RS.10.00 MILLION OR MORE

 

Contract                           Number:  Contract                               Value:  Contract Title:

Dated:

 

[Name of Supplier] hereby declares that it has not obtained or induced the procurement of any contract, right, interest, privilege or other obligation or benefit from Government of Pakistan or any administrative subdivision or agency thereof or any other entity owned or controlled by it (GoP) through any corrupt business practice.

Without limiting the generality of the foregoing [Name of Supplier] represents and warrants that it has fully declared the brokerage, commission, fee etc. paid  or payable to anyone and not given or agreed to give and shall not give or agree to give to anyone within or outside Pakistan either directly or indirectly through any natural or juridical person, including its affiliate, agent, associate, broker, consultant, director, promoter, shareholder, sponsor or subsidiary, any commission, gratification, bribe, finder's fee or kickback, whether described as consultations fee or otherwise, with the object of obtaining or inducing the procurement of a contract, right, interest, privilege or other obligation or benefit in whatsoever form from GoP, except that which has been expressly declared pursuant hereto.

[Name of Supplier] certifies that it has made and will make full disclosure of all agreements and arrangements with all persons in respect of or related to the transaction with GoP and has not taken any action or will not take any action to circumvent the above declaration, representative or warranty.

[Name of Supplier] accepts full responsibility and strict liability for making and false declaration, not making full disclosure, misrepresenting fact or taking any action likely to defeat the purpose of this declaration, representation and warranty. It agrees that any contract, right interest, privilege or other obligation or benefit obtained or procured as aforesaid shall, without prejudice to any other right and remedies available to GoP under any law, contract or other instrument, be voidable at the option of GoP.

Notwithstanding any rights and remedies exercised by GoP in this regard, [Name of Supplier] agrees to indemnify GoP for any loss or damage incurred by it on account of its corrupt business practices and further pay compensation to GoP in an amount equivalent to ten time the sum of any commission, gratification, bribe, finder's fee or kickback given by [Name of Supplier] as aforesaid for the purpose of obtaining or inducing the procurement of any contract, right, interest, privilege or other obligation or benefit in whatsoever form from GoP.

📑 Performance Guarantee Form (PGF)

Establishment of Online Examination System

Published on: Friday, September 25, 2026 11:00 AM

Ref# : P128944
QR Code

Performance Guarantee Form

 

To:     Federal Medical College (Federal Medical College), IT Assistant Federal Medical College, Hanna Road, G-8/4, Islamabad

 

WHEREAS [name of Bidder] (hereinafter called “the Bidder”) has undertaken, in pursuance of Contract No.  [reference number of the contract] dated [insert date] for provision of Goods(hereinafter called “the Contract”).

 

AND WHEREAS it has been stipulated by you in the said Contract that the Bidder shall furnish you with a Bank Guarantee by a reputable bank for the sum specified therein as security for compliance with the Bidder’s performance obligations in accordance with the Contract.

 

AND WHEREAS we have agreed to give the Bidders guarantee:

 

THEREFORE, WE hereby affirm that we are Guarantors and responsible to you, on behalf of the Bidder, up to a total of [amount of the guarantee in words and figures], and we undertake to pay you, upon your first written demand declaring the Bidder to be in default under the Contract and without cavil or argument, any sum or sums within the limits of [amount of guar­antee] as aforesaid, without your needing to prove or to show grounds or reasons for your demand or the sum specified therein.

 

This guarantee is valid until the: [insert date]

 

 

Signature and seal of the Guarantors

 

 

_____________________________________________________________________

[name of bank or financial institution]

 

 

_____________________________________________________________________

[address]

 

 

_____________________________________________________________________

[date}

📑 Annexure (ANX)

Establishment of Online Examination System

Published on: Friday, September 25, 2026 11:00 AM

Ref# : P128944
QR Code
No Annexure Defined.

📑 Procurement Forms (PFD)

Establishment of Online Examination System

Published on: Friday, September 25, 2026 11:00 AM

Ref# : P128944
QR Code